Crestron e-control Vote User Manual Download Page 128

Page: 128 / 135

Crestron

e-control Vote SW-VOTE

128

••

Appendices

Installation & Reference Guide — DOC. 5822

TallyTotal

Voting Console

Description

Total number of current votes

Direction

Voting Computer to control system

Type

Analog

Value

(where

= number of seats defined in signal block configuration)

Expected Reply

None

Comments

The total number of votes includes the sum of all Y

votes + all N

votes + all

abstentions. Excluded from this sum are all absentees, non-voters, and excused
voters.

Updated on any change to any seat at any time:

Reset to 0 on a new vote (following a

NewVote

pulse)

Updated in concert with all other “tally” signals

Sent in response to any

Yes, No,

Abstain

signal, and (possibly) any

Change

signal

See Also

Summary of Contents for e-control Vote








































































































































Search results

Summary of Contents for e-control Vote

Reviews:

Related manuals for e-control Vote

Brands by name

Popular brands

Crestron e-control Vote, User Manual

Search results

Summary of Contents for e-control Vote

Reviews:

Related manuals for e-control Vote

Brands by name

Popular brands