Crestron e-control Vote User Manual Download Page 124

Page: 124 / 135

Crestron

e-control Vote SW-VOTE

124

••

Appendices

Installation & Reference Guide — DOC. 5822

TallyCarried

Voting Console

Description

Motion carries

Direction

Voting Computer to control system

Type

Digital

Value

Assert:

Motion currently has sufficient votes to carry

De-assert:

Motion currently has insufficient votes to carrry

Expected Reply

None

Comments

The definition of “carries” is based on the signal block’s configuration. (See “The

Rules

Tab,” page 39.)

Updated on any change to any seat at any time:

Reset on a new vote (following a

NewVote

pulse)

Updated in concert with all other “tally” signals

Sent in response to any

Yes, No, Abstain,

Change

signal

See Also

TallyQuorum, Tally23Majority

Summary of Contents for e-control Vote








































































































































Search results

Summary of Contents for e-control Vote

Reviews:

Related manuals for e-control Vote

Brands by name

Popular brands

Crestron e-control Vote, User Manual

Search results

Summary of Contents for e-control Vote

Reviews:

Related manuals for e-control Vote

Brands by name

Popular brands