Crestron DMPS-100 Operation Manual Download Page 54

Page: 54 / 76

DigitalMedia Presentation Systems

Crestron

DMPS-100/200/300-C/300-C-AEC

•

DigitalMedia Presentation Systems: DMPS-100/200/300-C/300-C-AEC

Operations Guide – DOC. 7219D

Set the Auxiliary Output

Minimum Volume

The auxiliary output minimum volume control is used to set the lowest volume level

of the auxiliary output.
To set the auxiliary output minimum volume level:

Access the “Aux. 1 Output” or “Aux. 2 Output” menu as described on page

45.

Press the

buttons until

Min Volume

is displayed on the LCD and

press

ENTER

to display the “Aux. 1 Min Volume” menu.

“Aux. 1 Min Volume” Menu

Aux. 1 Min Volume

Adjust the auxiliary output minimum volume level with the

and

buttons. The highest auxiliary output minimum volume setting is 50%.

NOTE:

While adjusting the auxiliary output minimum volume level, the

auxiliary output volume level can be adjusted by turning the

VOLUME

control clockwise to raise the volume, or counterclockwise to lower the

volume. When adjusting the volume, the display changes to indicate the

volume level.

Press

MENU

ENTER

to save changes and return to the previous screen.

Set the Auxiliary Output

Maximum Volume

The auxiliary output maximum volume control is used to set the highest volume

level of the auxiliary output.
To set the auxiliary output maximum volume level:

Access the “Aux. 1 Output” or “Aux. 2 Output” menu as described on page

45.

Press the

buttons until

Max Volume

is displayed on the LCD and

press

ENTER

to display the “Aux. 1 Max Volume” menu.

“Aux. 1 Max Volume” Menu

Aux. 1 Max Volume

100%

Adjust the auxiliary output maximum volume level with the

and

buttons. The lowest auxiliary output maximum volume setting is 70%.

NOTE:

While adjusting the auxiliary output maximum volume level, the

auxiliary output volume level can be adjusted by turning the

VOLUME

control clockwise to raise the volume, or counterclockwise to lower the

volume. When adjusting the volume, the display changes to indicate the

volume level.

Press

MENU

ENTER

to save changes and return to the previous screen.

Summary of Contents for DMPS-100













































































Search results

Summary of Contents for DMPS-100

Reviews:

Crestron DMPS-100, Operation Manual, Page: 54 / 76

Search results

Summary of Contents for DMPS-100

Reviews: