Crestron DMPS-100 Operation Manual Download Page 50

Page: 50 / 76

DigitalMedia Presentation Systems

Crestron

DMPS-100/200/300-C/300-C-AEC

•

DigitalMedia Presentation Systems: DMPS-100/200/300-C/300-C-AEC

Operations Guide – DOC. 7219D

Set the

Program Minimum Volume

The “Prog. Min Volume” menu is used to set the lowest volume level of the program

output.
To set the program minimum volume level:

Access the “Program Output” menu as described on page 42.

Press the

buttons until

Min Volume

is displayed on the LCD and

press

ENTER

to display the “Prog Min Volume” menu.

“Prog. Min Volume” Menu

Prog. Min Volume

Adjust the program minimum volume level with the

and

buttons. The

highest program minimum volume level is 50%.

NOTE:

While adjusting the program minimum volume level, the program

volume level can be adjusted by turning the

VOLUME

control clockwise

to raise the volume, or counterclockwise to lower the volume. When

adjusting the volume, the display changes to indicate the volume level.

Press

MENU

ENTER

to save changes and return to the previous screen.

Set the

Program Maximum Volume

The “Prog. Max Volume” menu is used to set the highest volume level of the

program output.
To set the program maximum volume level:

Access the “Program Output” menu as described on page 42.

Press the

buttons until

Max Volume

is displayed on the LCD and

press

ENTER

to display the “Prog. Max Volume” menu.

“Prog. Max Volume” Menu

Prog. Max Volume

100%

Adjust the program maximum volume level with the

and

buttons. The

lowest program maximum volume setting is 70%.

NOTE:

While adjusting the program maximum volume level, the program

volume level can be adjusted by turning the

VOLUME

control clockwise

to raise the volume, or counterclockwise to lower the volume. When

adjusting the volume, the display changes to indicate the volume level.

Press

MENU

ENTER

to save changes and return to the previous screen.

Adjust the

Program Startup Volume

The “Prog. Startup Vol.” menu is used to establish the program output’s volume

level setting when an input is selected.
To adjust the program startup volume level:

Access the “Program Output” menu as described on page 42.

Press the

buttons until

Startup Vol.

is displayed on the LCD and

press

ENTER

to display the “Prog. Startup Vol.” menu.

Summary of Contents for DMPS-100













































































Search results

Summary of Contents for DMPS-100

Reviews:

Related manuals for DMPS-100

Brands by name

Popular brands

Crestron DMPS-100, Operation Manual

Search results

Summary of Contents for DMPS-100

Reviews:

Related manuals for DMPS-100

Brands by name

Popular brands