Crestron DMPS-100 Operation Manual Download Page 5

Page: 5 / 76

Crestron

DMPS-100/200/300-C/300-C-AEC

DigitalMedia Presentation Systems

Operations Guide – DOC. 7219D

Contents

•

Contents

DigitalMedia Presentation Systems: DMPS-100/200/300-C/300-C-AEC 1

Introduction ............................................................................................................................... 1

Features and functions ................................................................................................. 1

Applications................................................................................................................. 7

Internal Block Diagram ............................................................................................... 8

Specifications ............................................................................................................ 10

Physical Description .................................................................................................. 19

Setup ........................................................................................................................................ 29

Network Wiring ......................................................................................................... 29

CAT5 Wiring ............................................................................................................. 29

Installation ................................................................................................................. 30

Hardware Hookup ..................................................................................................... 32

Uploading and Upgrading ........................................................................................................ 36

Establishing Communication ..................................................................................... 36

Firmware ................................................................................................................... 37

IP Configuration ........................................................................................................ 38

DMPS Tool................................................................................................................ 38

Configuration & Operation ...................................................................................................... 39

Configuration............................................................................................................. 39

Default System Operation ......................................................................................... 63

Problem Solving ...................................................................................................................... 64

Troubleshooting ......................................................................................................... 64

Check Network Wiring .............................................................................................. 66

Reference Documents ................................................................................................ 67

Further Inquiries ........................................................................................................ 67

Future Updates .......................................................................................................... 68

Return and Warranty Policies .................................................................................................. 69

Merchandise Returns / Repair Service ...................................................................... 69

Crestron Limited Warranty ........................................................................................ 69

Summary of Contents for DMPS-100













































































Search results

Summary of Contents for DMPS-100

Reviews:

Crestron DMPS-100, Operation Manual, Page: 5 / 76

Search results

Summary of Contents for DMPS-100

Reviews: