Crestron DMPS-100 Operation Manual Download Page 12

Page: 12 / 76

DigitalMedia Presentation Systems

Crestron

DMPS-100/200/300-C/300-C-AEC

•

DigitalMedia Presentation Systems: DMPS-100/200/300-C/300-C-AEC

Operations Guide – DOC. 7219D

DMPS-100/200/300-C requires just one IP address for the complete DM network,

plus one additional IP address for the built-in control processor.

Integrated Control System

Its built-in 2-Series control system enables the DMPS-100/200/300-C to provide

complete, customizable control of every AV device, as well as room lighting,

window shades, and projection screens, without requiring a separate control

processor. The DMPS-100/200/300-C supports the full line of Crestron touch

screens, keypads, and wireless remotes for a user experience custom tailored to the

specific requirements of each end-user. Support for Crestron e-Control

, Crestron

Mobile

, Fusion RV

, and RoomView

applications delivers the industry's most

powerful platform for attaining remote access and centralized management using

computers and mobile devices.

CEC Embedded Device Control

The primary objective of every Crestron system is to enable precisely the control

desired for a seamless user experience. In addition to conventional IR, RS-232, and

Ethernet device control, the DMPS-100/200/300-C can provide an additional

alternative by harnessing the CEC (Consumer Electronics Control) signal embedded

in HDMI. The DMPS-100/200/300-C provides a gateway for controlling many

devices right through their HDMI connections, potentially eliminating the need for

any dedicated control wires or IR probes. Through proper CEC signal management,

the DMPS-100/200/300-C permits control of each device as desired.

Easy Setup

Every step of the DMPS-100/200/300-C setup process is designed to be quick and

easy using its front panel or Crestron Toolbox software, configuring inputs and

outputs automatically while letting the installer make intelligent design decisions

along the way. Out of the box, the DMPS-100/200/300-C’s front panel supports

basic signal routing for easy testing and troubleshooting during installation. The

front panel label strips can be customized using Crestron Engraver software or

standard 3/8" (~10 mm) tape labels, allowing for the clear designation of each input

and output. Inputs and outputs may also be designated by name through the software

to appear on the LCD display.

Summary of Contents for DMPS-100













































































Search results

Summary of Contents for DMPS-100

Reviews:

Related manuals for DMPS-100

Brands by name

Popular brands

Crestron DMPS-100, Operation Manual

Search results

Summary of Contents for DMPS-100

Reviews:

Related manuals for DMPS-100

Brands by name

Popular brands