Crestron DMPS-100 Operation Manual Download

Page: 48 / 76

DigitalMedia Presentation Systems

Crestron

DMPS-100/200/300-C/300-C-AEC

•

DigitalMedia Presentation Systems: DMPS-100/200/300-C/300-C-AEC

Operations Guide – DOC. 7219D

Program Output

The

Program Output

section of the “Audio Setup” menu is used to set the program

output source mix, bass, treble, program delay, minimum volume, maximum

volume, startup volume, and stereo/mono settings.

Access the

“Program Output” Menu

To access the “Program Output” menu:

Access the “Audio Setup” menu as described on page 40.

Press the

buttons until

Program Output

is displayed on the LCD

and press

ENTER

to display the “Program Output” menu.

To return to the “Audio Setup” menu, press

MENU.

Set the Program Source Mix

To set the program source mix:

Access the “Program Output” menu as described above.

Press the

buttons until

Source Mix

is displayed on the LCD and

press

ENTER

to display the “Program Source Mix” menu.

“Program Source Mix” Menu

Program Source Mix
Aud. Only

Press the

buttons until the desired setting is displayed on the LCD.

The current setting is indicated with an asterisk (*). The following settings

are available:

•

Aud. Only:

Sends the audio signal from the selected source to the

PROG OUT

connector.

•

Mic. Only

: sends the microphone input signal to the

PROG OUT

connector.

•

Mic + Aud

: Sends a mix of the audio signal from the selected

source and the microphone input signals to the

PROG OUT

connector.

NOTE:

While setting the program source mix, the program volume level

can be adjusted by turning the

VOLUME

control clockwise to raise the

volume, or counterclockwise to lower the volume. When adjusting the

volume, the display changes to indicate the volume level.

Press

ENTER

to save changes and return to the previous screen. To cancel

without saving changes, press

MENU

Set the Program Bass Level

To set the program bass level:

Access the “Program Output” menu as described above.

Press the

buttons until

Bass

is displayed on the LCD and press

ENTER

to display the “Program Bass” menu. The current bass level is

displayed.

“Program Bass” Menu

Program Bass

0dB

Summary of Contents for DMPS-100













































































Search results

Summary of Contents for DMPS-100

Reviews:

Related manuals for DMPS-100

Brands by name

Popular brands

Crestron DMPS-100, Operation Manual

Search results

Summary of Contents for DMPS-100

Reviews:

Related manuals for DMPS-100

Brands by name

Popular brands