Crestron CEN-NVS200 Operations & Installation Manual Download

Page: 81 / 92

Crestron

CEN-NVS200

Network Video Streamer

NOTE:

The “Maintenance” page can also be accessed by entering the following

URL in your Web browser:

http://

Video Streamer/

setup/maintain.html

Video Streamer

is the host name or IP address of the CEN-NVS200.

Refer to the following sections for information about maintenance actions.

Rebooting the CEN-NVS200

To reboot the CEN-NVS200, click

Reboot

below the

Reboot

pane of the

“Maintenance” page.

Restoring Factory Default Settings (Excluding Network
Settings)

To restore factory-default settings excluding the

NetworkType

settings on the

“Network” configuration page, click

Restore

below the

Restore

pane of the

“Maintenance” page. If

Network Type

is left unchecked (i.e., is not excluded),

Network settings must be configured again on the “Network” configuration page
(refer to “Configuring Network Settings” which starts on page 32 for information).

Exporting/Uploading Files

To export daylight savings time rules, custom language files and settings backup
files, click the appropriate

Export

button. To upload daylight savings time rules,

custom language files and settings backup files, click the appropriate

Browse

button

and select the file to upload, then click

Upload

Upgrading Firmware

To upgrade CEN-NVS200 firmware, click

Browse

, locate and select the firmware

file, then click

Upgrade

below the

Upgrade firmware

pane.

Operations & Installation Guide – DOC. 7111A

Network Video Streamer: CEN-NVS200

•

Summary of Contents for CEN-NVS200





























































































Search results

Summary of Contents for CEN-NVS200

Reviews:

Related manuals for CEN-NVS200

Brands by name

Popular brands

Crestron CEN-NVS200, Operations & Installation Manual

Search results

Summary of Contents for CEN-NVS200

Reviews:

Related manuals for CEN-NVS200

Brands by name

Popular brands