Creative Playthings SH 6100-000 Assembly Manual Download

Page: 1 / 24

MODEL #SH 6100-000

ASSEMBLY MANUAL

YORKTOWN

Please read the owner’s manual before assembling your play set.

It provides additional information on the care and use of your play set

You must carefully read the entire instruction manual before

proceeding with the assembly or use of your new play set.

This product is intended for single family home/residential use

only and not intended for use in any public setting. Placement in

any public setting constitutes a misuse of this product.

Creative Playthings takes great care to design its products with your child’s safety

in mind. However, only with careful supervision and proper safety instructions,

can you be assured of safe play time on any product designed for children.

The Yorktown gym is built using the frame of the Lexington gym as a

base structure. When assembling the this gym, set aside the Lexington

instructions and follow the steps in this document.

Summary of Contents for SH 6100-000

























Search results

Summary of Contents for SH 6100-000

Reviews:

Related manuals for SH 6100-000

Brands by name

Popular brands

Creative Playthings SH 6100-000, Assembly Manual

Search results

Summary of Contents for SH 6100-000

Reviews:

Related manuals for SH 6100-000

Brands by name

Popular brands