Creative Playthings SH 6100-000 Assembly Manual Download

Page: 22 / 24

YORKTOWN
19794-300 Rev J (05-20)

Page 22

ASSEMBLY INSTRUCTIONS

Step 35 — Mount Access Ladder:

Locate the two Access Ladder Brackets. Loosely fasten the

Access Ladder Brackets to the Access Ladder Assembly (N)

using one 5/16" x 1-1/2" Hex Bolt Assembly each, as shown.
Position the Access Ladder Assembly against the Platform

Support Side below the Access Ladder opening. Make sure

the bottom is securely on the ground.
Place the Access Ladder Brackets against the Platform Sup-

port as shown. Mark and drill 3/8" diameter holes through

the Platform Support. Fasten each Access Ladder Bracket

to the Platform Support using one 5/16 x 1-1/2" Hex Bolt

Assembly.
Note: The Access Ladder can be mounted on any side of

the gym desired, provided that its placement does not in-

terfere with other accessories. The Access Ladder should

be mounted well clear of any swing accessories. An effort

should be made to provide space to mount Entrance Wall

Slats and Hand Grips on either side of the Access Ladder.

Step 36 — Slide Mount:

Place the Slide Mount (I) tight against the Platform Support,

centered on the opening left for the slide. The beveled edge

of the Slide Mount should face the inside of the gym. Se-

cure the Slide Mount to the Platform Boards using four #10

x 2-1/2" Screws.
Drive the screws until the heads are flush with the top of the

Slide Mount. Do not over-tighten; over-tightening may cause

the points of the screws to protrude through the bottom of

the Platform Boards.

Step 37 — Slide:

Position the Slide on the Slide Mount (I) through the opening

prepared in earlier steps. Center the Slide in the opening

and pull it tight to the platform until it stops against the edge

of the Platform Support. Make sure and that the holes in the

Slide are over the Slide Mount.
Check that the Slide extends out perpendicular from the play

set.
Drill 5/16" holes through the Slide, Slide Mount and Platform

Boards using the holes in the Slide as a guide. Fasten the

slide using one 1/4 x 3" Truss Head Bolt and one 1/4" Weld

Nut for each hole.
Note: In some positions, a Stringer may be encountered

when drilling. Stop drilling, remove the Platform Board and

insert the Weld Nut into the hole from below. Reinstall the

Platform Board and continue with assembly. It may help to

clear space for the Weld Nut but using a 1" paddle bit on the

underside of the Platform Board

Your set-up will look different

Summary of Contents for SH 6100-000

























Search results

Summary of Contents for SH 6100-000

Reviews:

Related manuals for SH 6100-000

Brands by name

Popular brands

Creative Playthings SH 6100-000, Assembly Manual

Search results

Summary of Contents for SH 6100-000

Reviews:

Related manuals for SH 6100-000

Brands by name

Popular brands