![background image](http://html1.mh-extra.com/html/crary/john-deere-200/john-deere-200_owners-manual_2679354030.webp)
John Deere Air Reel Owner’s Manual
28
ASSEMBLY
RiGHT HAND DRivE KiT PARTS
KiT #
DEScRiPTiON
22738
RH DRIVE KIT, ROUND SHAFT (215 HEADER)
22739
RH DRIVE KIT, ROUND SHAFT (915 HEADER)
22741
RH DRIVE KIT, ROUND SHAFT (216 HEADER)
24051
RH DRIVE KIT, ROUND SHAFT (18”-20”)
24052
RH DRIVE KIT, ROUND SHAFT (22”-24”)
24103
RH DRIVE KIT, ROUND SHAFT (25”)
24053
RH DRIVE KIT, ROUND SHAFT (30”)
Refer to Figure 24 for the following steps:
Install the (Crary supplied) round clutch shaft into the
bearing through the RH side sheet of header. Reinstall
auger drive sprocket onto slip clutch shaft and secure
with 3/4” washer, castle nut and cotter pin.
Install the slip clutch onto the round clutch shaft and
secure with 3/4” washer, castle nut and cotter pin.
Remove the three 5/16” x 1-1/2” bolts from the gear
-
box sleeve on each side of the gearbox. Install two
bushings to the gearbox, aligning the keyways of the
bushings with each other at the 12:00 position. Install
the three 5/16” x 1-1/2” bolts to the bushings. Do not
tighten at this time.
Slide the gearbox shaft through the gearbox from
the left side. Insert the 5/16” x 1-1/2” keys into the
keyways of the round shaft and position the RH end
of the gearbox drive shaft within 1-1/2” of the LH end
of the clutch shaft.
Tighten the three bolts on the bushings on each side of
the gearbox to 15 ft-lbs. or 180 in-lbs. Tighten the set
screws on the bushings on each side of the gearbox
to secure the 5/16” X 1-1/2” keys into the keyways of
the gearbox shaft.
Install the drive sprocket onto the RH end of the gear
-
box drive shaft and secure with roll pin.
Align the slip clutch sprocket and sprocket on gearbox
drive shaft. Install the double roller chain to the drive
sprocket and slip clutch sprocket.
Attach the two shield mount brackets to the previously
drilled Ø13/32” holes. Install two 3/8” X 1” bolts and
3/8” serrated flange nuts to lower holes only. Attach
slip clutch shield to top holes of shield mount brackets
and install 3/8” hardware. Install and tighten remaining
bolts to shield assembly.
1.
2.
3.
4.
5.
6.
7.
8.
Reinstall auger drive chain onto sprocket and tighten
(see header owner/operator’s manual for the correct
chain tension).
Reinstall RH header shield and secure with lynch pins
or quick lock pins.
Slide the bushing shield weldment over the gearbox
drive shaft and secure to LH side of gearbox using two
1/2” bolts and 1/2” washers.
Install bearings and flangettes to bearing mount plate,
slide onto LH end of gearbox drive shaft and secure
temporarily to vertical upright on back of header.
Measure between bearing and gearbox bushing for
correct length, and cut drive shaft shield to measured
dimension.
Remove bearing mount plate, slide drive shaft shield
onto gearbox drive shaft and reinstall bearing and
mount plate.
Check for shaft alignment up & down and front & back.
Tighten the bolts securing the gearbox mounting plate
to the gearbox and the bolts securing the gearbox
mounting plate to the mount plate support.
Tighten the lock collar on the bearing. Insert a punch
in the collar dimple. Tap the collar in the direction of
shaft rotation to lock. Then, tighten the lock collar set
screw.
For 25’ and 30’ headers, bolt shield mount plate to
bearing mount plate. For all other header sizes bolt
shield mount plate directly to LH side of gearbox.
Insert a 5/16” X 1-1/2” key into keyway at the left end of
gearbox shaft. Slide the clutch end of the PTO driveline
onto the gearbox shaft and tighten set screws.
Slide the slip clutch shield over the PTO driveline and
fasten to the shield mount plate using the 5/16” X 3/4”
bolts.
Install the driveline bracket support to vertical upright
closest to feeder house using 3/8” X 3/4” carriage
bolts. The combine end of driveline will cradle in this
bracket.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
4.11 RiGHT HAND DRivE KiT - 200, 900 SERiES, 1-1/4” ROUND DRivE SHAFT
WARNiNG
Place all controls in neutral or off, lower header to the
ground, stop combine engine, set parking brake, re-
move ignition key, chock wheels and wait for all moving
parts to stop before servicing, adjusting, repairing, or
unplugging.
iMPORTANT
Correct shaft alignment is critical.
NOTE
Steps 11-14 apply to 25’ and 30’ headers. For all other
headers, skip to Step 15.