![background image](http://html1.mh-extra.com/html/crary/john-deere-200/john-deere-200_owners-manual_2679354065.webp)
John Deere Air Reel Owner’s Manual
63
OPERATION
5.7 TRANSPORTiNG
The Air Reel is designed to be easily and conveniently
moved from location to location. When transporting the
machine, review and follow these safety instructions:
Make sure you are in compliance with all local regula-
tions regarding transporting equipment on public roads
and highways.
It is the responsibility of the owner to know the light-
ing and marking requirements of the local highway
authorities and to install and maintain the equipment
to provide compliance with the regulations. Add extra
lights when transporting at night or during periods of
limited visibility.
See the owner’s manual that came with your combine
and header for proper transportation guidelines.
1.
2.
3.
The reel tines should lift the crop high enough to pass
over the guards for easier cutting.
Adjust the air direction as low as possible, with the
nozzles at a 90
°
angle to the down crop.
It is recommended that the cutterbar be adjusted to the
retracted position when cutting down, tangled crops.
•
•
•
5.6 OPERATiNG HiNTS
5.8 STORAGE
After the season’s use, the machine should be thoroughly
inspected and prepared for storage. Repair or replace any
worn or damaged components to prevent any unneces-
sary down time at the start of the next season. To ensure
a long, trouble free life, this procedure should be followed
when preparing the unit for storage:
Clear the area of bystanders, especially small chil-
dren.
Thoroughly wash the entire machine using a pressure
washer to remove all dirt, mud, debris or residue.
Inspect the following components:
PTO Driveline Components
Check the condition and operation of the
friction disc torque limiter (slip clutch).
Release slip clutch pressure.
Store in a dry place.
1.
2.
3.
A.
•
•
•
Electrical System
Check the wiring harness and all wiring
components for damaged or worn areas.
Check for cracked or worn insulation.
Replace any components that have come
in contact with moving parts and re-route
to prevent damage in the future.
Hydraulic Components:
Check all hydraulic lines for damage; re-
place as required.
Air Reel Components
Air Tubes: repair or replace bent or dam-
aged air tubes.
Plastic Tines: repair or replace bent or
damaged plastic tines.
Manifold Driveshaft Bearings: Driveshaft
bearings are sealed bearings and do not
need lubrication. If worn or damaged,
replace as required.
Idler Gears and Bearing Components,
Pinion Gears and Bearing Components
and Internal Gear sections: Check gears
for wear; check for worn or damaged bear-
ings and replace as required; adjust gears
as required.
Plastic Eccentric Rollers: check for un
-
even wear; replace as required.
Right Hand Drive Components
Roller Chain, Sprockets and Bearings:
check for wear; replace as required.
Visually inspect fan rotor for wear or
buildup.
Check condition of the rotary screen
bearings.
Make a list of all parts needed for repairs and order
them immediately. Repairs can then be done when
time permits and prevent unnecessary down time at
the start of next season.
Lubricate all grease points to remove any water resi
-
due from the washing and prevent rusting during the
storage period. Rotate all moving parts to distribute
lubricant to all surfaces.
Apply a light coat of grease on the shafts.
Check the cutterbar, reel area and drives for entangled
material.
Touch up all paint nicks and scratches to prevent
rusting.
B.
•
•
•
C.
•
D.
•
•
•
•
•
E.
•
•
•
4.
5.
6.
7.
8.