CR Remeha Quinta Pro 115 Installation And Service Manual Download Page 32

Page: 32 / 92

4. Connect the pump connection cable to the cable bundle by

opening and closing the cable bundle bands.

4.8.5.

Connecting a third party control unit

Connecting modulating controller

OpenTherm

regulator

The boiler is fitted with a

OpenTherm

connection as standard.

As a result, modulating

OpenTherm

controllers can be connected

without further modifications (Room, weather-dependent and

cascade controllers). The boiler is also suitable for

OpenTherm

Smart Power

In the case of a room controller: Install the regulator in the

reference room (generally the living room).

Connect the two-wire cable to terminals

On/off-OT

of the

connector.

If the tap water temperature can be set on the

OpenTherm

controller, then the boiler supplies this

temperature, with the set value on the boiler as the

maximum.

T002049-B

T000776-D

On/off

Tout

Tdhw

On/off

Tou

Tdhw

4. Installation

Quinta Pro 30 - 45 - 65 - 90 - 115

250413 - 123157-03

Summary of Contents for Quinta Pro 115





























































































Search results

Summary of Contents for Quinta Pro 115

Reviews:

Related manuals for Quinta Pro 115

Brands by name

Popular brands

CR Remeha Quinta Pro 115, Installation And Service Manual

Search results

Summary of Contents for Quinta Pro 115

Reviews:

Related manuals for Quinta Pro 115

Brands by name

Popular brands