background image

fig. 47 Restore factory settings 

LT.AL.W7H.000.052

 

2.11 Putting the boiler out of operation 

The boiler must be switched off and allowed to cool down before any maintenance or 
repairs are carried out. If the central heating system is not going to be used for a 
long time (during the holidays, forn instance, or frost-free periods) it is advisable to 
put the boiler out of operation. 

2.11.1 Boiler with frost protection, during longer periods of non-use 

 

Set the room thermostat or other controls to a low temperature, e.g. 10°C, 

 

Switch setting 

[P][4]

 to 

[1]

 (Eco mode), this will switch off the heat retention 

function. 

Now the boiler will only start working to protect itself against freezing. With external 
frost protection, the boiler can also prevent the central heating system from freezing. 

2.11.2 Boiler without frost protection, during longer periods of non-use 

 

Turn time clock off and allow system to cool down then isolate mains power 
supply at the fused spur unit. 

 

Isolate the gas supply at the boiler valve. 

 

Drain the boiler and central heating system if you will not be using the home 

for a long period and there is a chance of night frost. 

page 38 

 

3 INSPECTION AND MAINTENANCE 

The Remeha Avanta is practically maintenance free but should be inspected 
annually. 

 

If during the annual inspection the flue gas analysis indicates that the 

values are outside the figures given in 

table 10

maintenance work should be carried 

out as described in 

par. 3.2

. 

Also carry out maintenance if the ionisation read-out value is lower than 3 or higher 
than 9µA, or when the flame core is not correct. 

Summary of Contents for Avanta 12v















































































































Reviews: