Control Techniques Unidrive HS30 Quick Start Manual Download Page 53

Page: 53 / 66

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

Motor Rpm

= 60 x Frequency / Pole pairs

where
Pole pairs = the numeric value of

Number Of Motor Poles

(Pr

) (i.e. 3 for a 6 pole motor)

The frequency used to derive the

Motor Rpm

is the

Final Demand Reference

(Pr

). The maximum

and minimum values allow for a 10% over-shoot of the speed.
* With the Unidrive HS30, the maximum is 180,000.0 rpm

Current Magnitude

is the instantaneous drive output current scaled so that it represents the r.m.s.

phase current in Amps under steady state conditions.

Torque Producing Current

is the instantaneous level of torque producing current scaled so that it

represents the r.m.s. level of torque producing current under steady state conditions.

Digital I/O Read Word

reflects the state of digital inputs/outputs 1 to 5 and the relay.

Reference On

, which is controlled by the drive sequencer, indicates that the reference from the

reference system is active.

Motor Rpm

Num

±33000.0 rpm*

RFC-A

Current Magnitude

Num

0 to Drive Maximum Current A

RFC-A

Torque Producing Current

Num

± Drive Maximum Current A

RFC-A

Digital I/O Read Word

Bin

0 to 2047

RFC-A

Reference On

Bit

Off (0) or On (1)

RFC-A

Summary of Contents for Unidrive HS30



































































Search results

Summary of Contents for Unidrive HS30

Reviews:

Related manuals for Unidrive HS30

Brands by name

Popular brands

Control Techniques Unidrive HS30, Quick Start Manual

Search results

Summary of Contents for Unidrive HS30

Reviews:

Related manuals for Unidrive HS30

Brands by name

Popular brands