Control Techniques Unidrive HS30 Quick Start Manual Download Page 44 | Manualshive

Page: 44 / 66

background image

44

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

Set to the number of poles of the motor. The auto mode calculates the number of motor poles from
the settings of Pr

07

and Pr

39

.

Defines the drive output mode, which can either be a voltage mode or a current mode.

Determines the boost level when Pr

41

is set to Fd, SrE or Fd.tap modes.

40

Number Of Motor Poles

RW

Num

US

OL

Ú

Auto (0) to 32 (16)

Ö

Auto (0)

RFC-A

41

Control Mode

RW

Txt

US

OL

Ú

Ur.S (0), Ur (1), Fd (2), Ur.Auto (3),

Ur.I (4), SrE (5), Fd.tap (6)

Ö

Ur.I (4)

RFC-A

Value

Text

Description

0

Ur.S

Stator resistance and voltage offset measured at each start

1

Ur

No measurements

2

Fd

Fixed boost mode.

3

Ur.Auto

Stator resistance and voltage offset measured at first drive enable

4

Ur.I

Stator resistance and voltage offset measured at each power-up

5

SrE

Square law characteristic

6

Fd.tap (6)

Fixed boost with taper

The drive default setting is Ur I mode which means that the drive will carry out an autotune
every time the drive is powered-up and enabled. If the load is not going to be stationary
when the drive is powered-up and enabled, then one of the other modes should be
selected. Not selecting another mode could result in poor motor performance or OI.AC,
It.AC or OV trips.

42

Low Frequency Voltage Boost

RW

Num

US

OL

Ú

0.0 to 25.0 %

Ö

3.0 %

RFC-A

NOTE

«
...
42
43
44
45
46
...
»

Summary of Contents for Unidrive HS30



































































Reviews:

No comments

Related manuals for Unidrive HS30

Brand: Parker Pages: 30

Brand: VAT Pages: 22

Brand: Aaeon Pages: 76

Brand: Access Pages: 12

Brand: Daikin Pages: 56

Brand: Danfoss Pages: 36

Brand: Quectel Pages: 95

Brand: ICAS Pages: 51

Brand: Icar Pages: 40

Brand: Icar Pages: 86

Brand: Icar Pages: 39

Brand: IBP Pages: 12

Brand: jbc Pages: 44

Brand: jbc Pages: 8

Brand: Rachio Pages: 2

Brand: OMC Pages: 18

Brand: Paradox Pages: 2

Brand: Paradox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands