Control Techniques Unidrive HS30 Quick Start Manual Download Page 37

Page: 37 / 66

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

If the preset reference has been selected (see Pr

), the speed at which the motor runs is

determined by these parameters.
See

Drive Configuration

(Pr

This parameter and

Status Mode Parameter 1

(Pr

) define which parameters are displayed in

Status mode. The values can be alternated by pressing the Escape key, if the drive is running.

See

Status Mode Parameter 2

(Pr

This parameter defines the scaling applied to

Status Mode Parameter 1

(Pr

). The scaling is only

applied in the Status mode.

If any number other than 0 is programmed into this parameter, user security can be applied so that
no parameters except Pr

can be adjusted with the keypad. When this parameter is read via a

keypad it appears as zero. Refer to the

Control User Guide

for further information.

18 to 21

Preset Reference 1 to 4

Num

0.00 to Pr

0.00 Hz

RFC-A

Status Mode Parameter 2

Num

0.000 to 30.999

4.020

RFC-A

Status Mode Parameter 1

Num

0.000 to 30.999

2.001

RFC-A

Customer Defined Scaling

Num

0.000 to 10.000

1.000

RFC-A

User Security Code

Num

0-9999

RFC-A

Summary of Contents for Unidrive HS30



































































Search results

Summary of Contents for Unidrive HS30

Reviews:

Related manuals for Unidrive HS30

Brands by name

Popular brands

Control Techniques Unidrive HS30, Quick Start Manual

Search results

Summary of Contents for Unidrive HS30

Reviews:

Related manuals for Unidrive HS30

Brands by name

Popular brands