Control Techniques Unidrive HS30 Quick Start Manual Download Page 16 | Manualshive

Page: 16 / 66

background image

16

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

4.3.1 Use of residual current device (RCD)

There are three common types of ELCB / RCD:
1. AC - detects AC fault currents
2. A - detects AC and pulsating DC fault currents (provided the DC current reaches zero at least

once every half cycle)

3. B - detects AC, pulsating DC and smooth DC fault currents

•

Type AC should never be used with drives.

•

Type A can only be used with single phase drives

•

Type B must be used with three phase drives

If an external EMC filter is used with an ELCB / RCD, a delay of at least 50 ms should be
incorporated to ensure spurious trips are not seen. The leakage current is likely to exceed the trip
level if all of the phases are not energized simultaneously.

4.4 Control terminal configurations and wiring

The setting of Pr

05

automatically sets the drive configuration.

Action will only occur if the drive is inactive and no User Actions are running. Otherwise, the
parameter will return to its pre altered value on exit from edit mode. All parameters are saved if this
parameter changes.

Only type B ELCB / RCD are suitable for use with 3 phase inverter drives.

05

Drive Configuration

RW

Txt

PT

US

OL

Ú

AV (0), AI (1), AV.Pr (2), AI.Pr (3),

PrESEt (4), PAd (5), PAd.rEF (6),

E.Pot (7), torquE (8), Pid (9)

Ö

AV (0)

RFC-A

Value

Text

Description

0

AV

Analog input 1 (voltage) or Analog input 2 (voltage) selected by terminal
(Local/Remote)

1

AI

Analog input 1 (current) or Analog input 2 (voltage) selected by terminal
(Local/Remote)

2

AV.Pr

Analog input 1 (voltage) or 3 presets selected by terminal

3

AI.Pr

Analog input 1 (current) or 3 presets selected by terminal

4

PrESEt Four presets selected by terminal

5

PAd

Keypad reference

6

PAd.rEF Keypad reference with terminal control

7

E.Pot

Electronic Potentiometer

8

torquE

Torque mode, Analog input 1 (current frequency reference) or Analog input 2
(voltage torque reference) selected by terminal

9

Pid

PID mode, Analog input 1 (current feedback source) and Analog input 2
(voltage reference source)

WARNING

«
...
14
15
16
17
18
...
»

Summary of Contents for Unidrive HS30



































































Reviews:

No comments

Related manuals for Unidrive HS30

Brand: Zolix Instruments Pages: 22

COOPER POWER SERIES

Brand: Eaton Pages: 50

Brand: fakro Pages: 16

Brand: e-BLEACH Pages: 24

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brand: Oceanic Systems Pages: 8

PowerFlex 755 IP00

Brand: Allen-Bradley Pages: 78

Brand: Seneca Pages: 4

Home easy HE-440

Brand: CH Byron Pages: 2

Brand: RTI Pages: 2

Level-Trac LT-310

Brand: QTS Pages: 12

Brand: Sames Pages: 84

UNDER CONTROL CP-28

Brand: G-Force Pages: 2

Brand: HANYOUNG NUX Pages: 4

Brand: Z-Wave Pages: 44

HydroGuard 1430 Series

Brand: Powers Pages: 8

Brand: ccei Pages: 16

Brand: Nacon Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands