Control Techniques Unidrive HS30 Quick Start Manual Download Page 52

Page: 52 / 66

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

Open loop mode:

Final Demand Reference

shows the fundamental drive output frequency from the

Post Ramp

Reference

and the

Hard Frequency Reference

RFC mode:

Final Demand Reference

shows the reference at the input to the frequency controller, which is the

sum of the

Post Ramp Reference

, if the ramp output is not disabled and the hard frequency

reference (if enabled). If the drive is disabled

Final Demand Reference

shows 0.00.

Voltage across the internal DC bus of the drive.

Open loop mode:

The

Output Frequency

is the sum of the

Post Ramp Reference

and the motor slip compensation

frequency.

RFC-A mode:

The output frequency is not controlled directly, but the

Output Frequency

is a measurement of the

frequency applied to the motor.

The

Output Voltage

is the r.m.s line to line voltage at the a.c. terminals of the drive.

Final Demand Reference

Num

-Pr

to Pr

or Pr

to Pr

RFC-A

D.C. Bus Voltage

Num

0 to 415 V or 0 to 830 V

RFC-A

Output Frequency

Num

± 550.00 Hz

RFC-A

Output Voltage

Num

0 to 325 V or 0 to 650 V

RFC-A

Summary of Contents for Unidrive HS30



































































Search results

Summary of Contents for Unidrive HS30

Reviews:

Related manuals for Unidrive HS30

Brands by name

Popular brands

Control Techniques Unidrive HS30, Quick Start Manual

Search results

Summary of Contents for Unidrive HS30

Reviews:

Related manuals for Unidrive HS30

Brands by name

Popular brands