background image

 

EMM-R4h EMM-

μ

4h 

instruction manual 

IM441-U v0.7 

pag. 6  

DESCRIPTION FRONT PANEL– OPERATORS 

LEGEND: 

A

push-button for the visualization of electrical parameters of three-phase system with the corresponding LED 
indication. In modality programming (SETUP) it’s used to confirm the parameter set. 

B

push-button for the selection of the electrical parameter to be displayed on display 

F

. In modality programming 

(SETUP) it’s used to increase the value of the parameters to set.

 

C

push-button for the selection of the electrical parameter to be displayed on display 

G

. In modality programming 

(SETUP) it’s used to reduce the value of the parameters to set. 

D

LED bar for the indication of the electrical parameter displayed on display 

F

E

LED bar for the indication of the electrical parameter displayed on display 

G

F

3 displays for the visualization of every phase measures. When 

L

 LED is ON, only the main display will be active 

showing the three-phase system value of the measure selected. LED 

k

 and 

M

 show the eventual multiplying factor: 

k=kilo=x1000, M=Mega=x1000000. Using the 

C

 key the display indicates also the values of the active, reactive and 

apparent energy counters. Using the 

A

 and 

B

 keys the display indicates the maximum and average values. 

G

: display

 

for

 

the

 

visualization

 

of

 

the

 

measure

 

indicated

 

in

 

LED

 

E

 

(energy

 

counters

 

excluded).

 

The

 

voltage

 

values

 

are

 

referred

 

to

 

the

 

three-phase

 

system.

 

The

 

k

 

LED

 

displays

 

the

 

reading

 

in

 

kilo

 

(x1000).

 

Using

 

the

 

C

 

key

 

the

 

display

 

indicates

 

the

 

type

 

of

 

the

 

energy

 

displayed.

 

Using

 

the

 

A

 

and

 

B

 

keys,

 

the

 

display

 

indicates

 

the

 

type

 

of

 

average

 

or

 

maximum

 

value. 

A+C

: when pressing simultaneously the instrument pass to the following menu: instrument programming (

SETUP

), 

energy counters and peak values deleting (

RESET

), digital outputs programming (

SET

 

DO1

;

 

SET

 

DO 2

) (only 

for version with digital output), hour counter programming (

HR_

), I/O diagnostic page. 

A+B

: when pressing simultaneously the instrument pass to the visualization of average and maximum values stored. 

 

MENU OF INSTRUMENT PROGRAMMING (

SETUP

To

 

enter

 

in

 

SETUP

 

it’s

 

necessary

 

to

 

press

 

at

 

the

 

same

 

time

 

A

 

and

 

C

 

keys,

 

on

 

the

 

F

 

display

 

will

 

appear

 

the

 

message

 

SETUP

.

 

Pressing

 

the

 

A

 

key

 

on

 

the

 

G

 

display

 

will

 

appear

 

the

 

message

 

SET

 

that

 

will

 

remain

 

always

 

displayed

 

during

 

the

 

set

 

of

 

each

 

parameter

 

to

 

highlight

 

the

 

SeTUp

 

phase

 

in

 

running.

 

The

 

set

 

values

 

will

 

be

 

keep

 

also

 

in

 

absence

 

of

 

auxiliary

 

power

 

supply. 

B

C

D

E

F

A

G

k

M

k

V

L-N

L1

L2

L3

L

Hz

electrical

multi meter

V

A

P.F.

W

VAr

VA

V

L-N

L-L

°C

V

L-L

alarm

kWh

kVArh

...h

max

avg

max

maxD

avg

EMM

DIGITAL OUTPUTS

Digital outputs:
the DO1 output is used as PULSE and it's linked
to the ACTIVE energy counter,
the DO2 output is used as PULSE and it's linked
to the REACTIVE energy counter.
DO1 and DO2 can be used as ALARM and
linked to a measured parameter.

Max 150mA
Max 230Vac/dc

Summary of Contents for EMM-M4H

















Reviews: