manualshive.com logo in svg

Contrel EMM-M4H, Instruction Manual, Page: 2 / 16

Share
Download
Contrel EMM-M4H Instruction Manual Download Page 2

 

EMM-R4h EMM-

μ

4h 

instruction manual 

IM441-U v0.7 

pag. 2  

INSTALLATION 

WARNING FOR THE USER 
Read carefully the instructions/indications contained in this manual before installing and using the instrument. 
The instrument described in this manual is intended for use by properly trained staff only. 
SAFETY 
This instrument has been manufactured and tested in compliance with EN 61010-1standards. In order to maintain these conditions and 
to ensure safe operation, the person must comply with the indications and markings contained in the manual. When the instrument is 
received, before beginning installation, check that it's O.K. And it has not suffered any damage during transport. When starting 
installation make sure that the operating voltage and mains voltage are compatible with the device instructions. The instrument power 
supply must not be earthed. Maintenance and/or repair must be carried out only by qualified and authorized personnel. If there is ever 
the suspicious that, that there is a lack of safety ,during operation, the instrument must be disconnected and cautions taken against 
accidental use. 

Operation is no longer safe when: - The instrument doesn't work. / - The measured value are obviously wrong or 
unreasonable / - There is clearly visible damage. / - After serious damage incurred during transport. / - After a storage under 
unfavourable conditions 

 

CONNECTION 

For a correct use of the device, the wiring diagram contained in the present manual, must be respected. 
The connections are available on the screw terminal: 

 

-  auxiliary power supply: 

The power supply is take from voltage inputs. 
Are available 3 different auxiliary supply: 
 

0 - 115V = 100-130V 50-60Hz 

(N-L3) 

(on request) 

 

0 - 230V = 220-240V 50-60Hz 

(N-L3) 

(on request) 

 

0 - 400V = 380-415V 50-60Hz 

(L2-L3) 

(standard model) 

It’s possible, for example, to give an auxiliary power supply between phase and neutral, in a 4 wires system, or phase-
phase in a 3 wires system, without neutral or from a VT in a medium voltage application. 

In the standard version the voltage is 400V and it’s taken between the phases L2-L3. 

In the following table it’s possible to see the measurable voltage depending of the type of power supply. 

power supply terminals 

rated voltage 

range of measurable voltage 

L2-L3

 (phase to phase power supply) 

400V 

300÷500V phase to phase (175÷290V phase-neutral) 

230V 

175÷290V phase to phase (130÷170V phase-neutral) 

110V 

85÷145V phase to phase (50÷85V phase-neutral) 

L3-N

 (phase – neutral power supply) 

230V 

300÷500V phase to phase (175÷290V phase-neutral) 

110V 

175÷290V phase to phase (100÷170V phase-neutral) 

The standard version allows to apply the instrument at all the three-phase network 400V with or without neutral supplied. 
For example for application on single phase 230V will need the L3-N / 230V. while for applications in medium voltage (for 
example using external voltage transformer 15 / 0.1 kV phase to phase) will need the version L2-L3 / 110V. 

 

-  measure voltage inputs:

 

 

4 terminals are available for the connection to 
the 3 phase and neutral of the network of 
measure, the maximum voltage phase to 
phase shouldn't be over 500 V rms and 
dependent to the auxiliary power supply. In 
case of a 3 phase system without neutral, or 
non distributed neutral to leave terminal N 
free. It’s possible to use external voltage 
transformer in fact the transformation rate of 
the external transducer can be set in the 
SETUP of the instrument and the 
visualization allows the reading of voltage up 
to 40,0 kV. 

 

-  measure current inputs: 

4 terminals are available for the connection to 
3 external amperometric transformers with secondary 5A, it’s possible to use 2 TA on lines with 3 wires (insertion three 
phase Aron). The utilization of external TA is obligatory. The transformation rate of the external transducer can be set in 
the SETUP of the instrument and the visualization allows the reading of voltage up to 9,99 kA. 

 

REMARKS

: It's a must to respect the phase sequence. The connections between current and voltage phase inputs must not be 

inverted (for example, CT placed on phase L1 must correspond to the I1 input). So as it is not correct to invert S1 and S2 terminals, 
since power factors and powers might not be reliable. 
For fixing the flush mount version instrument to the panel, use the fixing devices supplied, by inserting them in the side groves of the 
enclosure and tighten the screws. 
For safety reasons, place an external fuse protection at the input voltages, and use adequate cables for the working voltages and 
currents, with a cross sections from 0,5 to 2,5 mm

2

. 

ENERGY COUNTERS

REAR PANNEL

extractible screw terminal

EMM-R4h

EMM-µ4h

Summary of Contents for EMM-M4H

















Reviews:

No comments