FSG/MTM/001 060511
152
Error Code and Description
Refer to page:
ERROR 60-30: IMx, SCSI 0 register error
ERROR 60-31: IMx, SCSI 0 FIFO error
ERROR 60-32: IMx, SCSI 1 reset error
ERROR 60-33: IMx, SCSI 1 register error
ERROR 60-34: IMx, SCSI 1 FIFO error
ERROR 60-82: IMx, USB chip error
ERROR 60-83: IMx, wrong board version installed
ERROR 60-85: IMx, 1394 chip error
ERROR 70-86: MDAx, Unable to communicate with board
ERROR 70-87: MDAx, Failure on ATAC movement
ERROR 70-219: Fan error
ERROR 70-221: LMx, Board error
7.4 Troubleshooting Hints
The scanner does not power-up
•
Check the power supply connections.
•
Check that all cable connectors are properly inserted into their sockets.
•
Check voltages on the SMPS.
•
Check the supply voltages on the LME-, CBE/CBF-, IMB/IMD, and SUC-Boards.
Error 08-147, ‘Invalid Scanner ID’
•
Error 08-147 indicates that the DIP Switch (pos. 4, 5, 6, 7, and 8) on the Operator
Panel is set to an undefined scanner type or inconsistency between the detected
scanner hardware and the Scanner ID switch setting, see Section 3.10.4, page 54.
•
Error 08-147 may also indicate a bad connection between the SUC-Board and the
Operator Panel.
Error 08-149, Invalid Smart Card
•
The Smart Card is not valid for this scanner type.
•
Error 08-149 may also indicate a bad connection between the SUC-Board and the
Smart Card Reader.
Error 08-208, Keyboard check failed
•
Check cable to Operator Panel.
•
Replace Operator Panel.
Error 30-140 to 30-143, Light Profile Correction Failed (Color Channels)
Error 30-240 to 30-243, Light Profile Correction Failed (B/W Channel)
Error 30 is displayed if more than 200 consecutive pixels or a total of 1500 pixels cannot be
adjusted up to the required White-Signal Level.
•
Error 30 is most often caused by dirt on the Glass Plate or the White Background Plate
and the first step should be to make sure that these parts are clean.
Summary of Contents for CHAMELEON 25
