3
USER RESPONSIBILITY
Service to this product should only be performed by CONCOA or an authorized CONCOA agent. Requests for service may be made
through CONCOA CUSTOMER SERVICE at 1-800-225-0473. Written requests may be made using CONCOA’s FAX number at 1-
757-422-3125 or CONCOA’s E-MAIL at [email protected]
CONCOA accepts no responsibility for damage or injury if this product is modified in any way. CONCOA assumes/accepts no
liability or responsibility for damage to individuals or equipment that may occur when using this product.
SAFETY
THIS PRODUCT IS NOT INTENDED FOR USE WITH TOXIC GASES, FLAMMABLE GASES OR CORROSIVE GASES.
NOTICE
The Medical IntelliSwitch™ is intended for use in medical installations. This product meets NFPA-99
requirements for switchover systems. Compliance with NFPA-99 for a complete installation (ie Cylinders, piping,
alarms, etc.) are the responsibility of the installer. Refer to NFPA-99 for complete system requirements.
Basic safety precautions must be followed to reduce the risk of fire, electrical shock or injury.
•
Connect the Medical IntelliSwitch™ to the correct line voltage. A label on the product identifies what voltage it is wired for.
CONNECTION TO AN INCORRECT VOLTAGE CAN CAUSE SERIOUS DAMAGE TO THE PRODUCT AND WILL
VOID ANY WARRANTY.
•
While the Medical IntelliSwitch™ Switchover is dust and moisture resistant, it is NOT water-proof or completely sealed. It
should be installed where it will not be subjected to rain or high concentrations of dust. Never pour or spray liquids directly
onto the product.
•
Install the Medical IntelliSwitch™ where the ambient temperature range is between 0° F and 140° F.
•
Do not install this product in a hazardous environment.
•
If product appears damaged in any way, do not use and request service from CONCOA.
•
Consult the cylinder distributor for the proper use of cylinders and for any restrictions on their use (such as flow rate and
temperature requirements).
•
Store cylinders with valve caps screwed on, and chain cylinders to a supporting wall or column.
•
Handle cylinders carefully and only with valve caps screwed on. The cap will reduce the chance that the cylinder valve will
break off if the cylinder is accidentally dropped or falls over. The cap also protects the cylinder valve from damage to screw
threads, which could cause leaky connections.
•
No smoking should be permitted near oxygen, nitrous oxide, any other oxidizer, flammable gases, or flammable mixtures, or
in areas where cylinders are stored.
•
Where an oxidizer (such as nitrous oxide or oxygen) is used, the manifold and cylinders must be kept clean. No oil, grease, or
combustible substances should come in contact with oxygen or nitrous oxide storage or handling equipment. Such materials
in contact with oxygen or nitrous oxide are readily ignitable and, when ignited, will burn intensely.
•
Never lift gas cylinders with a magnetic lifting device.
•
Never use an open flame when leak testing.
•
Always open valves slowly when high-pressure gases are being used.
•
Always be sure that a cylinder contains the correct gas before connecting it to any manifold.
•
Always leak-test any manifold or distribution pipeline before using.
•
Always be sure that the gas in a pipeline is the correct gas for the intended use.
•
Always close all cylinder valves before disconnecting cylinders from a manifold.
•
Always remove all empty cylinders from a manifold before connecting full cylinders.
•
Always test cylinders to be sure the cylinders are full before connecting to a manifold.
Summary of Contents for IntelliSwitch 57 Series
