Comtech EF Data LGAN Installation And Operation Manual Download Page 68

Page: 68 / 118

LGaN

Revision 0

Ethernet Interface Operation

4–28

MN-LGAN

4.5.4.6 Status | Statistics

This page shows stored statistics. Use it to configure how the LGaN handles and shows statistics.

Click

[Refresh]

to see the latest page data.

Figure 4-23. ‘Status | Statistics’ Page

Configure

Name

Description

Statistics Interval

Enter the interval at which statistics are logged. The interval is set in minutes. Minimum

resolution is 1 minute (001); maximum is 99 minutes (099). Default is 60 minutes (060).

Statistics Averaging

Select Enable or Disable to set the Statistics Averaging function:

•

If Enabled, statistics data is averaged at a rate of once per second for 10 seconds.

•

If Disabled, burst values are logged instead of averaged values.

Click Submit to save the changes.

Summary of Contents for LGAN























































































































Search results

Summary of Contents for LGAN

Reviews:

Related manuals for LGAN

Brands by name

Popular brands

Comtech EF Data LGAN, Installation And Operation Manual

Search results

Summary of Contents for LGAN

Reviews:

Related manuals for LGAN

Brands by name

Popular brands