CDM-625A Advanced Satellite Modem
MN-CDM625A
Appendix F
Revision 4
F–27
If the message shown begins with
OK,
then after approximately 5 seconds, the display
changes as per the following example:
The CnC Mode: APC,Side A,
C-
Band (Off, On, APC)
Suspend? N (Y,N) APC is active (
)
At this point, as indicated on the bottom line of the display, CnC-APC is
active
.
To suspend CnC-APC at any time: On the bottom line, which will be displaying
Suspend?
N (Y,N
),
use the
▲▼
arrow keys to select
Y(Yes)
and then press
ENTER
. The CnC-APC
status message on the bottom line of the display will update accordingly, as per the
following example:
The CnC Mode: APC,Side A,
C-
Band (Off, On, APC)
Activate? N (Y,N) APC is not active (
)
Note that, when CnC-APC is suspended, it is de-activated on
both
sides.
If a message other than
OK
is displayed after attempting to perform a re-balance,
the CnC-
APC system will not activate, and you should correct the link conditions before re-
attempting to activate it.
CAUTION – IMPORTANT NOTE:
When CnC-APC is active, you are not permitted to change configuration
parameters that potentially affect the operation of CnC-APC (modulation type,
FEC type, code rate, framing, etc). If you attempt to change one of these
parameters either locally or remotely, the change will not be accepted. In order
to change these configuration parameters, CnC-APC needs to be suspended first.
Following the changes, you should re-activate CnC-APC. Be aware that the re-
activation will be preceded with a new re-balance operation.
F.4.7 CnC-APC Redundancy Support Notes
1)
The CnC-APC feature fully supports 1:1 redundancy. Note that, as is required with standard
CnC 1:1 redundancy operation, a PMSI cable is required to connect the two units in a 1:1
pair.
Sect. 6.2.1.8.4 CONFIG: CnC
PMSI-Control (Chapter 6. FRONT PANEL
OPERATION)
2)
At this time, 1:N redundancy in the CRS-300/CRS-500 is not yet supported – a firmware
update for these switches will be available in the future. Please consult Comtech EF Data
Technical Support for updated information.
Summary of Contents for CDM-625A
