manualshive.com logo in svg

Comnet CNGE2FE16MS, Installation And Operation Manual

Share
Download
Comnet CNGE2FE16MS Installation And Operation Manual Download Page 98

inS_cnge2fe16MS_reV–

01/11/12     Page 98

INSTALLATION AND OPERATION MANUAL 

CNGE2FE16MS

TECh SUPPORT: 1.888.678.9427

Port Configuration

You can configure the 802.1x authentication state for each port. The state provides 

Disable, 

Accept, Reject, 

and

 Authorize

.

 

»

Reject

: The specified port is required to be held in the unauthorized state.

 

»

Accept

: The specified port is required to be held in the authorized state.

 

»

 Authorize

: The specified port is set to the 

Authorized

 or 

Unauthorized

 state in accordance with 

the outcome of an authentication exchange between the supplicant and the authentication 
server.

 

»

Disable

: When disabled, the specified port works without complying with 802.1x protocol.

 

»

Select 

Apply 

to have the configuration take effect.

Figure 89 – 802.1x Per Port Setting interface

Summary of Contents for CNGE2FE16MS

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands