Comnet CNGE2FE16MS Installation And Operation Manual Download Page 72

Page: 72 / 128

inS_cnge2fe16MS_reV–

01/11/12 Page 72

INSTALLATION AND OPERATION MANUAL

CNGE2FE16MS

TECh SUPPORT: 1.888.678.9427

802.1Q Configuration

Please follow the instructions below to configure the 802.1Q VLAN.

Select the pull-down menu to select

802.1Q

and select Apply to configure the VLAN

Operation Mode on 802.1Q.

Enable GVRP Protocol

: Select this checkbox to enable GVRP protocol. This checkbox is

available while the VLAN Operation Mode is set on

802.1Q

Management VLAN ID

: Only the VLAN members, whose Untagged VID (PVID) equals to

the value specified in this field, have permission to access the switch. The default value is

meaning this limit is not enabled (all members in different VLANs can access this switch).

After you have configured the three parameters, select the

Apply

button right beneath this

area to finish creating an 802.1Q VLAN.

Figure 69 – 802.1Q VLAN interface

On the 802.1Q Configuration tab, select the

Port

pull-down menu to select a port you want to

configure within the VLAN.

Summary of Contents for CNGE2FE16MS

































































































































Search results

Summary of Contents for CNGE2FE16MS

Reviews:

Related manuals for CNGE2FE16MS

Brands by name

Popular brands

Comnet CNGE2FE16MS, Installation And Operation Manual

Search results

Summary of Contents for CNGE2FE16MS

Reviews:

Related manuals for CNGE2FE16MS

Brands by name

Popular brands