Comnet CNGE2FE16MS Installation And Operation Manual Download Page 10

Page: 10 / 128

inS_cnge2fe16MS_reV–

01/11/12 Page 10

INSTALLATION AND OPERATION MANUAL

CNGE2FE16MS

TECh SUPPORT: 1.888.678.9427

LED Indicators

LED indicators located on the front panel display the power status and network status of the
CNGE2FE16MS. Please Table 1 for further details.

LED

Color

Description

PWR

Green

System power on

Off

No power inputs

R.M.

Green

The switch is the master device of the X-ring group

Off

Non-master device

PWR1

Green

Power input 1 is active

Off

Power input 1 is inactive

PWR2

Green

Power input 2 is active

Off

Power input 2 is inactive

P-Fail
(depends on the Fault
Relay Alarm configuration)

Red

Power or Ethernet port linking failure occurs

Off

No failure occurs

P1 ~ P16

Green

Connected to network

Blinking Data is transmitting or receiving
Off

Not connected to network

Amber

Full duplex

Blinking Collision of packets occurs
Off

Half duplex or not connected to network

P17, P18
(10/100/1000T)

Green
(Upper LED)

Connected to network

Blinking Data is transmitting or receiving
Off

Not connected to network

Green
(Lower LED)

Operating at speed of 1000M

Off

Disconnected or operating at speed of 10/100M

P17, P18
(100/1000 SFP)

Green

Connected to network

Blinking Data is transmitting or receiving
Off

Not connected to network

Table 1 – Definition of LED indicators

Summary of Contents for CNGE2FE16MS

































































































































Search results

Summary of Contents for CNGE2FE16MS

Reviews:

Related manuals for CNGE2FE16MS

Brands by name

Popular brands

Comnet CNGE2FE16MS, Installation And Operation Manual

Search results

Summary of Contents for CNGE2FE16MS

Reviews:

Related manuals for CNGE2FE16MS

Brands by name

Popular brands