Comnet CNGE2FE16MS Installation And Operation Manual Download Page 28

Page: 28 / 128

inS_cnge2fe16MS_reV–

01/11/12 Page 28

INSTALLATION AND OPERATION MANUAL

CNGE2FE16MS

TECh SUPPORT: 1.888.678.9427

Select the

Connection

SSH

node of the tree-menu to configure options for controlling SSH

connections.

Tick the check box labeled

Don’t start a shell or command at all

Figure 26 – Options Controlling SSH Connections

Select the

Connection

SSH

Tunnel

node of the tree-menu to configure options for

controlling SSH port forwarding.

Tick the check box labeled

Local ports accept connection from other hosts

that allows you

to set up local-to-remote port forwards (including dynamic port forwards) in such a way that
machines other than your client PC can connect to the forwarded port.

Add a new forwarded port to connect to the SSH server and set the type to

Local

Figure 27 – Options Controlling SSH Port Forwarding

Summary of Contents for CNGE2FE16MS

































































































































Search results

Summary of Contents for CNGE2FE16MS

Reviews:

Related manuals for CNGE2FE16MS

Brands by name

Popular brands

Comnet CNGE2FE16MS, Installation And Operation Manual

Search results

Summary of Contents for CNGE2FE16MS

Reviews:

Related manuals for CNGE2FE16MS

Brands by name

Popular brands