Cole Parmer Jenway 7410 Instruction Manual Download Page 38 | Manualshive

Page: 38 / 68

background image

38

9.2

Calibration

The calibration must be performed at the same wavelength at which the sample will be measured. Insert a cuvette

containing the blank solution into the sample chamber and close the instrument lid. Touch the

icon. This sets

the instrument to zero absorbance and 100% transmittance.

9.3

Sample Measurement

It is not possible to measure a sample before the instrument has been calibrated at the selected wavelength. Once
the calibration has been performed the Sample icon becomes active and a sample can be measured. Remove the
cuvette containing the blank solution and place a cuvette containing the sample to be measured in the sample

holder. Close the instrument lid and touch the

icon.

«
...
36
37
38
39
40
...
»

Summary of Contents for Jenway 7410





































































Reviews:

No comments

Related manuals for Jenway 7410

Brand: Magnetic Instrumentation Pages: 63

Brand: Landis+Gyr Pages: 54

Brand: VELOCICALC Pages: 6

Brand: Panametrics Pages: 68

Brand: P3 International Pages: 2

YPP-100 Light Piano

Brand: Yamaha Pages: 54

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 56

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 32

Brand: YOSensi Pages: 3

Brand: Neogen Pages: 9

Multifunction Compensator

Brand: Halcyon Pages: 20

SensoDirect Con200

Brand: Lovibond Pages: 24

Brand: OHAUS Pages: 28

Brand: Velp Scientifica Pages: 32

Brand: Bender Pages: 52

Brand: LaserLiner Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands