manualshive.com logo in svg

Coemar Panorama Cyc 250 C., Instruction Manual, Page: 8 / 29

Share
Download
Coemar Panorama Cyc 250 C. Instruction Manual Download Page 8

7.3 Warning

safety chain

When hanging the 

Panorama Cyc 250 C

we recommend the use of a safety chain (cod. 069), affixed to the appropriate hole

(B) on the yoke of the 

Panorama Cyc 250 C

and to the suspension device.

This secondary safety attachment should be done using either a metal wire rope or a metal chain, both suitably rated for the pur-
pose.

risk of fire

Every projector produces head, and should therefore be installed in a well-ventilated position. The minimum distance from flamma-
ble materials: 0,5m. The minimum distance from the object being illuminated: 2 m.

cabling

The mains cable provided is thermally resistant, complying to the most recent international standards.

NB: 

In case of cable replacement, similar cable with comparable thermal resistant qualities must be used exclusively (cable 3x1.5 ø exter-

nal 10 mm, rated 300/500V, tested to 2KV, operating temperature -40° +180°.

coemar

cod. CV5309).

mains connection

Panorama Cyc 250 C

can operate at voltages from 

100V-115V-208V-230V-240V

at 

50

or 

60Hz

(operating voltage and

frequency can be selected as described in section 6 and 19 of this manual). Prior to connecting the unit to your mains supply, ensu-
re that the model in your possession correctly matches the mains supply available to you.
For connection purposes, ensure your plug is of a suitable rating: 

at 

230 V

: 2 Amps on startup, 1,6 amps constant draw in normal operation

a 

115 V:

4,2 Amps on startup, 3,2 amps constant draw in normal operation

Locate the mains cable which exits the base of the unit and connect as shown below:

protection

The use of a thermal magnetic circuit breaker is recommended for each 

Panorama Cyc 250 C

.

A good earth connection is essential for the correct operation of the fixture. Strict adherence to regulatory norms is strongly recom-
mended.

Panorama Cyc 250 C. must be earthed; never install the unit unless the yellow/green earth cable is secu-

rely connected.

massa/ground

neutro/neutral

fase/live

marrone - brown

blu - blue

giallo/verde - yellow/green

alimentazione

main

8. Mains connection

8

English

Summary of Contents for Panorama Cyc 250 C.






























Reviews:

No comments