manualshive.com logo in svg

Coemar Panorama Cyc 250 C., Instruction Manual, Page: 28 / 29

Share
Download
Coemar Panorama Cyc 250 C. Instruction Manual Download Page 28

The Panorama Cyc 250 C. 

allows for the electronic alignment of the projector’s motors. This procedure is performed by 

coemar

at the factory. It may be useful to perform this procedure in the case of internal components being replaced.
Altering the factory settings may radically alter the functioning of the projector. Carefully read all of the following prior to 
attempting any changes.

electronic calibration

IMPORTANT NOTE:

This procedure can only be undertaken if the projector is correctly receiving 

DMX 512

signal.

To undertake this procedure:
1) Select a 

DMX

number as required from 

1

to 

512

by moving the respective dip-switches to the 

ON

position, whilst simulta-

neously selecting the 

motor calibration. 

From this moment on, the third 

DMX

channel pertaining to this fixture, say 

DMX 3

, no longer allows for program selection, (as

shown in the 

DMX

table),but now controls the motor offset of the colour wheel. The other functions on respective channels

DMX 1

,

2

and 

4

remain the same.

For example, DMX address 1:

2) Insert a colour into the beam of light controlled by 

DMX

1

3) Adjust the offset (calibration) of the colour wheel by utilising control channel 

DMX 3

.

4) Check the alignment of the individual colour in the optical path of the projector controlled by channel 1.
5) When the desired offset has been obtained, press the reset button to record the calibration setting.

c h a n n e l

f u n c t i o n

type of control

e f f e c t

d e c i m a l

1

c o l o u r s

step

Open/white

0 - 2 4

step or proportional

depending on

channel 2

colour 1

2 4 - 4 9

step or proportional

depending on

channel 2

colour 2

5 0 - 7 4

step or proportional

depending on

channel 2

colour 3

7 5 - 9 9

step or proportional

depending on

channel 2

colour 4

1 0 0 - 1 2 7

proportional

Forwards rainbow effect from fast to slow

1 2 8 - 1 9 0

step

No  rotation

1 9 1 - 1 9 2

proportional

Backwards rainbow effect from slow to fast

1 9 3 - 2 5 5

2

colour mode

step

colours (channel 1) steps

0 - 1 2 7

step

colours (channel 1) proportional

1 2 8 - 2 5 5

3

colour wheel

o f f - s e t

proportional

proportional offset of the colour wheel motor, press reset button to record

0 - 2 5 5

4

L a m p   o n / o f f /

r e s e t

step

Park (no function)

0 - 1 0

program wait

time control

step

lamp off

1 1 - 3 0

step

motor  reset (only once)

3 1 - 6 0

step

Program stop

6 1 - 8 0

proportional

Selected auto-program pause time control (1 sec/5 min)

8 1 - 2 4 1

step

lamp on

2 4 2 - 2 5 5

ON

ON

dip-switches

1

2

4

8

16

32

64

128

256

motor

calibration

Attention

This section is reserved for technicians and persons with technical experience only.

24. Electronic motor alignment

28

English

Summary of Contents for Panorama Cyc 250 C.






























Reviews:

No comments