manualshive.com logo in svg

Cobalt Digital Inc 9932-EMDE, Product Manual, Page: 94 / 104

Share
Download
Cobalt Digital Inc 9932-EMDE Product Manual Download Page 94

3

Troubleshooting

3-56

9932-EMDE PRODUCT MANUAL

9932EMDE-OM (V1.4)

9932-EMDE Card Edge Status/Error Indicators and Display

Figure 3-7 shows and describes the 9932-EMDE card edge status indicators 
and display. These indicators and the display show status and error conditions 
relating to the card itself and remote (network) communications (where 
applicable). Because these indicators are part of the card itself and require no 
external interface, the indicators are particularly useful in the event of 
communications problems with external devices such as network remote 
control devices.

Figure 3-7  9932-EMDE Card Edge Status Indicators and Display

9932-EMDE

4-Character Alphanumeric Display

COM

REF

ERR

IN A

IN B

IN C

IN D

Input Active

Indicators

Status/Error

Indicators

Item

Function

Alphanumeric
Display

Shows card statuses (

BOOT

 (card booting), (

9932-EMDE

 (card up and OK))

COM LED

Blue LED flashes when 9932-EMDE is receiving control message from remote network control (e.g., 
DashBoard™ or Cobalt

®

 Remote Control Panel)

REF LED

NA

ERR LED

This function is currently reserved.

Input Active 
LEDs

Blue LEDs for each SDI input (A thru D) indicate signal presence for each corresponding card SDI input. No 
illumination of any of the LEDs indicates the 9932-EMDE has not locked onto a valid signal on any input.

Summary of Contents for 9932-EMDE









































































































Reviews:

No comments