manualshive.com logo in svg

Cobalt Digital Inc 9932-EMDE, Product Manual, Page: 46 / 104

Share
Download
Cobalt Digital Inc 9932-EMDE Product Manual Download Page 46

3

Checking 9932-EMDE Card Information

3-8

9932-EMDE PRODUCT MANUAL

9932EMDE-OM (V1.4)

Checking 9932-EMDE Card Information

The operating status and software version the 9932-EMDE card can be 
checked using DashBoard™ or the card edge control user interface. Figure 
3-5 shows and describes the 9932-EMDE card information screen using 
DashBoard™ and accessing card information using the card edge control user 
interface.

Note:

Proper operating status in DashBoard™ is denoted by green icons for the sta-
tus indicators shown in Figure 3-5. Yellow or red icons respectively indicate 
an alert or failure condition. Refer to Troubleshooting (p. 3-55) for corrective 
action.

Figure 3-5  9932-EMDE Card Info/Status Utility

The Tree View shows the cards seen by DashBoard™. 
In this example, Network Controller Card is hosting a 
9932-EMDE card in slot 18. 

Status Display

This displays shows the status and format of the signals being 
received by the 9932-EMDE, as well as card status. 

Card Info Display

This displays (alternately 
selected in the Card Info 
pane) shows the the card 
hardware and software 
version info, as well as a 
Cobalt code number for the 
currently installed rear 
module. 

Summary of Contents for 9932-EMDE









































































































Reviews:

No comments