Cobalt Digital Inc 9932-EMDE Product Manual Download Page 5 | Manualshive

Page: 5 / 104

Cobalt Digital Inc 9932-EMDE Product Manual Download Page 5

9932EMDE-OM (V1.4)

9932-EMDE PRODUCT MANUAL

1-1

Chapter 1

Chapter 1

Introduction

Overview

This manual provides installation and operating instructions for the
9932-EMDE 3G/HD/SD-SDI 16- Channel Embedder / De-Embedder with
Audio/Video Processing and CVBS I/O card (also referred to herein as the
9932-EMDE).

This manual consists of the following chapters:

•

Chapter 1, “Introduction” – Provides information about this manual
and what is covered. Also provides general information regarding the
9932-EMDE.

•

Chapter 2, “Installation and Setup” – Provides instructions for
installing the 9932-EMDE in a frame, and optionally installing a
9932-EMDE Rear I/O Module.

•

Chapter 3, “Operating Instructions” – Provides overviews of
operating controls and instructions for using the 9932-EMDE.

This chapter contains the following information:

•

9932-EMDE Card Software Versions and this Manual (p. 1-2)

•

Manual Conventions (p. 1-3)

•

Safety and Regulatory Summary (p. 1-5)

•

9932-EMDE Functional Description (p. 1-6)

•

Technical Specifications (p. 1-19)

•

Warranty and Service Information (p. 1-22)

•

Contact Cobalt Digital Inc. (p. 1-23)

«
...
3
4
5
6
7
...
»

Summary of Contents for 9932-EMDE









































































































Reviews:

No comments