Cobalt Digital Inc 9932-EMDE Product Manual Download Page 23 | Manualshive

Page: 23 / 104

Cobalt Digital Inc 9932-EMDE Product Manual Download Page 23

9932EMDE-OM (V1.4)

9932-EMDE PRODUCT MANUAL

1-19

Introduction

Technical Specifications

Note:

If network remote control is to be used for the frame and the frame has not yet

been set up for remote control, Cobalt

®

reference guide Remote Control

User Guide (PN 9000RCS-RM) provides thorough information and
step-by-step instructions for setting up network remote control of Cobalt

®

cards using DashBoard™. (Cobalt

®

OGCP-9000 and OGCP-9000/CC

Remote Control Panel product manuals have complete instructions for setting
up remote control using a Remote Control Panel.)

Download a copy of this guide by clicking on the Support>Reference
Documents link at www.cobaltdigital.com and then select DashBoard
Remote Control Setup Guide as a download, or contact Cobalt

as listed in

Contact Cobalt Digital Inc. (p. 1-23).

9932-EMDE Rear I/O Modules

The 9932-EMDE physically interfaces to system video connections at the rear
of its frame using a Rear I/O Module.

All inputs and outputs shown in the 9932-EMDE Functional Block Diagram
(Figure 1-1) enter and exit the card via the card edge backplane connector.
The Rear I/O Module breaks out the 9932-EMDE card edge connections to
BNC and other connectors that interface with other components and systems
in the signal chain.

The full assortment of 9932-EMDE Rear I/O Modules is shown and described
in 9932-EMDE Rear I/O Modules (p. 2-4) in Chapter 2, “Installation and
Setup”.

Technical Specifications

Table 1-1 lists the technical specifications for the 9932-EMDE 3G/HD/
SD-SDI 16-Channel Embedder / De-Embedder with Audio/Video Processing
and CVBS I/O card.

Table 1-1

Technical Specifications

Item

Characteristic

Part number, nomenclature

9932-EMDE 3G/HD/SD-SDI 16-Channel Embedder /
De-Embedder with Audio/Video Processing and CVBS I/O

Installation/usage environment

Intended for installation and usage in frame meeting openGear™
modular system definition

Power consumption

< 18 Watts maximum

Installation Density

Up to 20 cards per 20-slot frame

Environmental:

Operating temperature:
Relative humidity (operating or storage):

32° – 104° F (0° – 40° C)
< 95%, non-condensing

Frame communication

10/100 Mbps Ethernet with Auto-MDIX

«
...
21
22
23
24
25
...
»

Summary of Contents for 9932-EMDE









































































































Reviews:

No comments