manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Product Manual, Page: 91 / 118

Share
Download
Cobalt Digital Inc 9922-FS Product Manual Download Page 91

9922FS-OM (V1.5)

9922-FS PRODUCT MANUAL

3-49

Operating Instructions

9922-FS Function Menu List and Descriptions

Keyer

Provides key/fill insertion controls and displays 
insertion status.

Key/fill controls described below only appear on cards with +KEYER licensed optional feature. This feature 

requires a Rear Module that accommodates separate key/fill video inputs. Note that on cards also licensed with +KEYER, Wings 
and Keyer controls appear on the same tab.

•  Key/Fill Source Controls

Selects the card SDI input video ports to serve as the card’s key and fill 

sources.

Note: SDI inputs selected must be used on Rear I/O Module 

correspondingly equipped with intended input ports.

•  Key Mode Control

Selects key mode as follows:

• Alpha Ramp setting is used when typical key/fill is provided by key/fill 

generator with separate key and fill outputs. 

• Alpha Threshold or Reverse Alpha Threshold setting is used to 

provide keying using a combined key/fill signal derived from a simple 
graphic source. 

•  Key/Fill Insertion Enable Control

Key Enable control sets up key/fill for insertion. When enabled, key 
preview is available on Key Preview output.

When key preview shows desired results, Apply Key To Program can be 
enabled to apply the key/fill to the program video output.

Table 3-2

9922-FS Function Menu List — continued

Summary of Contents for 9922-FS























































































































Reviews:

No comments