manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Product Manual, Page: 36 / 118

Share
Download
Cobalt Digital Inc 9922-FS Product Manual Download Page 36

2

Installing a Rear I/O Module

2-6

9922-FS PRODUCT MANUAL

9922FS-OM (V1.5)

RM20-9922-FS-E

Provides the following connections:

• Four 3G/HD/SD-SDI video inputs (SDI IN A thru 

SDI IN D)

• Eight AES audio inputs (AES IN 1 thru AES IN 8)

• Four 3G/HD/SD-SDI video outputs; selectable as 

processed or input reclocked out
(SDI PROC/RCK OUT 1 thru
SDI PROC/RCK OUT 4)

• Eight AES audio outputs

(AES OUT 1 thru AES OUT 8)

Note: Available equipped with High-Density BNC 

(HDBNC) or DIN1.0/2.3 connectors as:
RM20-9922-FS-E-HDBNC or 
RM20-9922-FS-E-DIN, respectively.

1930D

RM20-9922-FS-F

Provides the following connections:

• Two 3G/HD/SD-SDI video input BNCs (SDI IN A 

and SDI IN B)

• Three 3G/HD/SD-SDI video output BNCs

(SDI OUT 1A thru SDI OUT 4B; each GUI 
selectable as selected-input reclocked or 
processed out)

• One relay-protected SDI processed output BNC

(RLY BYP A/B OUT)

• Two opto-isolated GPI inputs (terminals GPI 1-G 

and GPI 2-G)

• Two opto-coupled GPO (GPO 1/G and GPO 2/G)

Note: Refer to GPIO, Serial (COMM), and Analog 

Audio Connections (p. 2-11) for connector 
pinouts and important information regarding 
GPO electrical limits.

1928

Table 2-1

9922-FS Rear I/O Modules — continued

9922-FS Rear I/O Module

Description

Summary of Contents for 9922-FS























































































































Reviews:

No comments