manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Product Manual, Page: 53 / 118

Share
Download
Cobalt Digital Inc 9922-FS Product Manual Download Page 53

9922FS-OM (V1.5)

9922-FS PRODUCT MANUAL

3-11

Operating Instructions

9922-FS Function Menu List and Descriptions

Table 3-2

9922-FS Function Menu List

Input Video Controls

Allows manual or failover selection of card SDI 
program video inputs and displays status and raster 
format of received SDI video.

• Input Video Source

Selects the input video source to be applied to the card’s program video 

input.

• SDI A and SDI B choices allow forced manual selection of 

correspondingly SDI IN A or SDI IN B.

• Failover A to B sets main path preference of SDI IN A.

- If SDI IN A goes invalid, then SDI IN B is selected. 
- If SDI IN A goes valid again, failover automatically reverts to

SDI IN A.

• Failover B to A sets main path preference of SDI IN B.

- If SDI IN B goes invalid, then SDI IN A is selected. 
- If SDI IN B goes valid again, failover automatically reverts to

SDI IN B.

• SDI C and SDI D choices allow forced manual selection of 

correspondingly SDI IN C or SDI IN D without failover choices.

• CVBS – select CVBS input as the program video input.

Note: Failover criteria via this control is simple signal presence.

• Input Video Status

Displays input status of each video input, along with elapsed time of 
signal acquire.

SDI A thru SDI D and CVBS Status show raster/format for all card 
inputs. If signal is not present or is invalid, Unlocked is displayed. 
(These status indications are also propagated to the Card Info 
pane.)

Note: Status display shows maximum card input complement. 

Input complement is determined by rear I/O module used.

Summary of Contents for 9922-FS























































































































Reviews:

No comments