manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Product Manual, Page: 47 / 118

Share
Download
Cobalt Digital Inc 9922-FS Product Manual Download Page 47

9922FS-OM (V1.5)

9922-FS PRODUCT MANUAL

3-5

Operating Instructions

Control and Display Descriptions

Web HTML5 User Interface

(See Figure 3-4.) When equipped with a rear I/O module having an Ethernet 
port, the 9922-FS controls can be accessed via a web network connection with 
no additional remote control software needed. The web GUI shows the same 
tabs, controls and status displays as those accessed using DashBoard™. This 
allows very convenient control access to the card, even if using a computer 
without DashBoard remote control or in case the frame network connection is 
down.

The card can be accessed in a web browser by entering the card IP address as 
set in the card 

Admin

 tab. (See Admin (Log Status/Firmware Update - Card 

IP Address) (p. 3-63) for more information.)

Note:

Card must be equipped with a rear I/O module with an Ethernet port to use 
html access. The card address is entirely independent of, and requires no 
association with, the frame openGear IP address.

Figure 3-4  Typical Web GUI Tabs and Controls

Typical web GUI Menu tabs

Typical web GUI controls and status displays

1

0.

9

9.

1

1.

1

1

9

I

P

:

The card edge alphanumeric 
display, along with card model ID, 
shows a scrolling message 
showing current card IP address 
(in this example, 10.99.11.119)

Summary of Contents for 9922-FS























































































































Reviews:

No comments