manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Product Manual, Page: 115 / 118

Share
Download
Cobalt Digital Inc 9922-FS Product Manual Download Page 115

9922FS-OM (V1.5)

9922-FS PRODUCT MANUAL

3-73

Operating Instructions

Troubleshooting

Note:

• (TTS only) Cards shipped with TTS use an SD card for the 

TTS library in addition to recovery files. If your +TTS-equipped device was 
received earlier than December 2015, your SD may not contain the recov-
ery files. Contact Product Support to obtain the updated SD card containing 
both TTS library and SD recovery files.

• If unit is a BBG-1000 Series device, remove the top cover before 

proceeding.

.

Figure 3-10  SD Card Installation

2.

(See Figure 3-11.) With card powered-down, locate the 

MMC BOOT

 

button on the card. Proceed as shown in picture.

Figure 3-11  MMC Boot Button

1

From underside of card, locate 
the SD card receptacle

2

With SD card labeling facing up 
(as shown), gently push the 
card into the receptacle until it 
clicks and locks into place

Electronic device or assembly is susceptible 
to damage from an ESD event. Handle only 
using appropriate ESD prevention practices.

1

Press and hold MMC BOOT button

FRONT OF CARD

2

Power-up card and continue holding 
button for 3 seconds, then release 
button

Summary of Contents for 9922-FS























































































































Reviews:

No comments