manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Product Manual, Page: 62 / 118

Share
Download
Cobalt Digital Inc 9922-FS Product Manual Download Page 62

3

9922-FS Function Menu List and Descriptions

3-20

9922-FS PRODUCT MANUAL

9922FS-OM (V1.5)

Output Video Mode Controls

Allows selection of each of the four video output coaxial 
connectors as processed SDI out or reclocked SDI out. 
Also provides CVBS parameter controls and test 
pattern output controls for card CVBS output.

• Output Video Crosspoint

For each SDI output port supported by the card, provides a crosspoint for 

routing program processed video or selected-input reclocked to an SDI 
output.

In this example, SDI OUT 1 and SDI OUT 3 are receiving Program 

(procesed) video out, with SDI OUT 2 providing SDI IN A reclocked input 
video.

Note: Choices shown here are examples only. Key preview available 

only when equipped with +KEYER option.

Provides CVBS output parameter controls and test 
pattern output controls

• CVBS Oversampling and Color Controls

• Oversampling enables or disables video DAC oversampling. 

Oversampling can improve rendering of motion for down-conversions to 
the CVBS SD analog output.

• Color enables or disables chroma content in the CVBS output. 

• CVBS Test Pattern Generator Control

Enables manual insertion (replacement) of CVBS output video to instead 
output 75% color bars.

Table 3-2

9922-FS Function Menu List — continued

Summary of Contents for 9922-FS























































































































Reviews:

No comments