Cleveland steamcraft 21-CET-8 Service Manual Download | Manualshive

Page: 40 / 139

background image

Page 32

Model 21 -CET-8 Service Manual

COOKING OPERATIONS - KEY PAD CONTROL PANEL

SteamCraft 3.1 cooking operations are simple and direct. Figure 3-3, to the
right, shows the operations that can be performed during a four-hour shift.
Each operation in the diagram is covered in a procedure in this chapter. The
diagram, in conjunction with the control panel summary on page 31, contains
enough information for rudimentary (quick start) operation of the SteamCraft
3.1. However, to maintain full warranty coverage, and for safe, efficient
operation of the SteamCraft 3.1, the operator must, at a minimum, comply
with all cautions, warnings and instructions in the detailed operating
procedures. The operator must be familiar with all the operating features
explained in this chapter before attempting to operate the SteamCraft 3.1
steamer.

Manual and Timed Modes

The SteamCraft 3.1 has two operating modes: manual and timed. The
TIMED/MANUAL rocker switch selects the operating mode. Pressing the
MANUAL end of the switch selects the manual operating mode. Pressing the
TIMED end of the switch selects the timed (automatic) operating mode.

• Manual Mode provides continuous steaming. The operator starts and

stops steaming operations manually.

•

Timed Mode provides automatic control of steaming operations. The timer

control starts and stops steaming operation, and monitors cooking time
and compartment temperature for accurate, efficient, uniform steam
cooking.

Cooking procedures are slightly different for each mode. The diagram in
Figure 3-3 illustrates which procedures are common to both modes and
which are specific to each mode.

Main Power Switch

Usually the SteamCraft 3.1 main power switch is left ON. If the main power
switch was left in the OFF position, turn it ON as follows.
1. Check that the water supply valves are open. 2.

Press the

OFF (bottom) end of the ON/OFF switch.

3. The TIMED/MANUAL switch and timer settings are not important in this

procedure. The control panel circuits are not powered while the ON/OFF
switch is set to OFF.

4. Refer to the main power switch in Figure 3-2, and turn on electric power

to the SteamCraft 3.1. The steamer will immediately start a blowdown
cycle. The blowdown cycle lasts 3 minutes.

NOTE:

If it is necessary to stop the blowdown cycle before it is finished,

turn the ON/OFF switch to ON. (Refer to Power ON and
Preheat.)

Printed 12/90

«
...
38
39
40
41
42
...
»

Summary of Contents for steamcraft 21-CET-8












































































































































Reviews:

No comments

Related manuals for steamcraft 21-CET-8

Brand: Pahlen Pages: 2

GK6750 GROOM PRO

Brand: UFESA Pages: 48

Brand: Braun Pages: 22

Brand: Gasmate Pages: 8

Brand: SUNWIND Pages: 22

Brand: MY-NO-NO Pages: 30

Oral-B PRO 1000

Brand: Braun Pages: 24

Brand: Dillenger Pages: 23

Brand: Fagor Pages: 51

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 5

Brand: Philips Pages: 14

Brand: Remington Pages: 36

Super Nimbus V12 Series

Brand: Sawo Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands