background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY SYMBOLS

WARNING: 

Do not direct discharge 

stream at persons or animals. Keep 
clear of nozzle.

WARNING:

 Never direct spray toward 

any electrical device or electrical 
outlet.

General Warning, indicates 
that failing to follow these 
instruction could result in 
injury or damage to the 
machine.

To reduce the risk of injury, 
read the manual before 
use.

ALWAYS 

wear safety glasses 

when using this machine.

WARNING: 

No open flame, 

open ignition source and 
smoking is prohibited

WARNING: 

No smoking 

DANGER:

 Risk  to 

breathing. Engine 
exhaust  fumes can kill. 
For outdoor use only. Work 
in a well ventilated area.

WARNING: 

Risk of injection 

or severe injury. Do not 
direct discharge stream at 
persons or animals. Keep 
clear of nozzle. This 
machine is to be used 
only by qualified operators.

WARNING:

 Risk of spray 

injury. Spray can propel 
objects. Always wear ANSI 
approved Z87.1 Safety 
Glasses.

WARNING:

 Risk of 

chemical burn. Never 
spray acids, corrosive or 
toxic chemicals. Use only 
cleaners formulated for 
pressure washers.

WARNING:

 Risk of 

electrocution. Never 
direct spray toward any 
electrical device or 
electrical outlet.

WARNING:

 R i s k   o f   u n s a f e  

o p e r a t i o n .   K e e p  
children away from this 
equipment. Gun kicks 
back. Hold with both hands.

WARNING:

 Risk of hot 

sur faces.

Recycle unwanted 

materials instead of 
disposing of them as waste. 
All tools, accessories and 
packaging should be 
sorted, taken to a recycling 
centre and disposed of in a 
manner which is compatible 
with the environment.

Summary of Contents for 7320202





























Reviews: