background image

20

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

CHANGING THE SPARK PLUGS

1. Remove the spark plug cap from the spark plug.

2. Use the supplied spark plug spanner to remove the spark plug.

3. Remove any carbon that has accumulated around the sparkplug.

4. Check the overall condition of the 

spark plug and replace if 
necessary.

5. Check the spark plug gap (a), it 

should be between 0.7 and 0.8 
mm, adjust if necessary.

6. Reinstall the spark plug and refit 

the spark plug cap.

LONG TERM STORAGE

For long term storage;

1. The petrol tank should be drained.

• Ensure that the engine is cold before draining the tank.

2. Remove the fuel tank cap and use a pump type sIphon to drain the petrol 

into an appropriate, clean container.

• Do not store petrol for long periods of time.

• Dispose of excess petrol in an environmentally safe way. Your local 

recycling centre can advise you on the best method of disposal.

3. After the petrol tank has been drained, start the engine and allow it to use 

any petrol that may remain in the engine, or fuel pipe.

4. Make sure that the power washer has been thoroughly cleaned before 

storing it in a clean dry place.

CAUTION: ALLOW THE ENGINE TO COOL BEFORE REMOVING THE SPARK 
PLUG.

Summary of Contents for 7320202





























Reviews: