Clarke 3110876 Operating & Maintenance Instructions Download | Manualshive

Page: 7 / 32

background image

7

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

COMPRESSED AIR REQUIREMENTS

A typical air line layout is shown below. If an automatic in-line filter/regulator is
used, it will keep the tool in good condition, but should be regularly checked
& topped up with oil. CLARKE air-line oil should be used and the lubricator
adjusted to approx 2 drops per minute.

Use only clean, dry, regulated compressed air as a power source.

Air compressors used with the tool must comply with the appropriate
European Community Safety Directives.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU
ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF
COMPRESSORS AND COMPRESSED AIR SYSTEMS.

«
...
5
6
7
8
9
...
»

Summary of Contents for 3110876

































Reviews:

No comments

Related manuals for 3110876

Brand: B&B Pages: 3

Brand: ABS Pages: 8

VisionXS-IP-C-DP-UHR

Brand: G&D Pages: 144

Brand: Gage Bilt Pages: 12

Brand: Gage Bilt Pages: 13

Brand: Gage Bilt Pages: 9

Brand: Gage Bilt Pages: 10

Brand: Lamello Pages: 156

Current Loop Supply M3LDY

Brand: M-system Pages: 6

Brand: Veit Pages: 70

7539-300X Series

Brand: Avdel Pages: 47

Brand: Xantrex Pages: 64

Brand: Parker Pages: 6

Brand: Haslux Pages: 8

Brand: BGS technic Pages: 4

Brand: Dritz Pages: 6

Brand: B+K precision Pages: 15

Brand: Kinetik Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands