Citrix ByteMobile T1010 Installation, Configuration And Administration Download Page 87

Page: 87 / 172

T-Series Traffic Director Installation, Configuration and Administration Guide

3-13

Configuring T1000 Data Plane for Layer-2 and Layer-3

Requested: media AUTO, speed AUTO, duplex AUTO, fctl OFF,

throughput 0

Actual: media FIBER, speed 10000, duplex FULL, fctl OFF, throughput 10000

5) Interface 10/3 (10G Ethernet, no SFP+ found) #4

flags=0xc023 <ENABLED, UP, UP, autoneg, HAMON, 802.1q, tagall>

MTU=1514, native vlan=1, MAC=00:1b:21:cf:14:08, uptime 14h23m22s

Requested: media AUTO, speed AUTO, duplex AUTO, fctl OFF,

throughput 0

Actual: media FIBER, speed 10000, duplex FULL, fctl OFF, throughput 10000

VMAC=00:00:5e:00:01:0a

6) Interface 10/4 (10G Ethernet, no SFP+ found) #6

flags=0xc023 <ENABLED, UP, UP, autoneg, HAMON, 802.1q, tagall>

MTU=1514, native vlan=1, MAC=00:1b:21:cf:13:9c, uptime 14h23m24s

Requested: media AUTO, speed AUTO, duplex AUTO, fctl OFF,

throughput 0

Actual: media FIBER, speed 10000, duplex FULL, fctl OFF, throughput 10000

VMAC=00:00:5e:00:01:0a

7) Interface 10/5 (10G Ethernet, fiber SFP+, 1/10 Gbits) #5

flags=0x4001 <disabled, DOWN, down, autoneg, 802.1q, tagall>

MTU=1514, native vlan=1, MAC=00:1b:21:cf:18:21, downtime 203h16m39s

Requested: media AUTO, speed AUTO, duplex AUTO, fctl OFF,

throughput 0

8) Interface 10/6 (10G Ethernet, fiber SFP+, 1/10 Gbits) #5

flags=0x4001 <disabled, DOWN, down, autoneg, 802.1q, tagall>

MTU=1514, native vlan=1, MAC=00:1b:21:cf:13:71, downtime 203h16m39s

Requested: media AUTO, speed AUTO, duplex AUTO, fctl OFF,

throughput 0

9) Interface 10/7 (10G Ethernet, fiber SFP+, 1/10 Gbits) #5

flags=0x4001 <disabled, DOWN, down, autoneg, 802.1q, tagall>

MTU=1514, native vlan=1, MAC=00:1b:21:cf:14:09, downtime 203h16m39s

Requested: media AUTO, speed AUTO, duplex AUTO, fctl OFF,

throughput 0

10) Interface 10/8 (10G Ethernet, no SFP+ found) #7

flags=0xc021 <ENABLED, UP, UP, autoneg, HAMON, 802.1q, tagall>

MTU=1514, native vlan=1, MAC=00:1b:21:cf:13:9d, uptime 14h23m18s

Requested: media AUTO, speed AUTO, duplex AUTO, fctl OFF,

throughput 0

Actual: media FIBER, speed 10000, duplex FULL, fctl OFF, throughput 10000

11) Interface LA/1 (802.3ad Link Aggregate) #11

flags=0x4100c023 <ENABLED, UP, AGGREGATE, UP, HAMON, 802.1q, tagall>

MTU=1514, native vlan=1, MAC=02:1b:21:cf:18:20, uptime 14h23m19s

Requested: media NONE, speed NONE, duplex NONE, fctl NONE,

throughput 0

Actual: throughput 20000

LA mode: AUTO

10/1: FIBER-10000-FULL-OFF UP 14h23m21s

10/2: FIBER-10000-FULL-OFF UP 14h23m22s

VMAC=00:00:5e:00:01:0a

12) Interface LO/1 (Loopback interface) #10

flags=0x20008021 <ENABLED, UP, UP>

MTU=1514, native vlan=1, MAC=00:25:90:64:ba:86, uptime 203h16m39s

Summary of Contents for ByteMobile T1010













































































































































































Search results

Summary of Contents for ByteMobile T1010

Reviews:

Brands by name

Popular brands

Citrix ByteMobile T1010, Installation, Configuration And Administration

Search results

Summary of Contents for ByteMobile T1010

Reviews:

Brands by name

Popular brands