Cisco VG202 Software Configuration Manual Download Page 29

Page: 29 / 50

4-3

Cisco VG202 and Cisco VG204 Voice Gateways Software Configuration Guide

OL-16191-01

Chapter 4 Configuring Voice

Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice Gateways

VG(config)#

ip routing

For complete information about global configuration commands, see the Cisco IOS configuration guides
and command references.

Step 6

To configure another interface, enter the

exit

command to return to the

VG(config)#

prompt.

Step 7

To configure the Cisco VG for voice traffic, see the VoIP references in the

“Prerequisites” section on

page 4-1

Step 8

To exit configuration mode and return to the enable prompt, when you finish configuring interfaces,
press

Ctrl-Z

. To see the current operating configuration, including any changes you just made, enter the

show running-config

command:

VG#

show running-config

To see the configuration currently stored in NVRAM, enter the

show startup-config

command

at the

enable prompt:

VG#

show startup-config

Step 9

The results of the

show running-config

and

show startup-config

commands differ if you have made

changes to the configuration but have not yet written them to NVRAM. To write your changes to
NVRAM and make them permanent, enter the

copy running-config startup-config

command at the

enable prompt:

VG#

copy running-config startup-config

Building configuration. . .

[OK]

VG#

The Cisco VG is now configured to boot in the new configuration.

Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice
Gateways

To configure auto-configuration on the Cisco VG202 and Cisco VG204 voice gateways, follow these
guidelines and procedures:

•

Restrictions for Configuring Auto-Configuration

•

Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice Gateways

•

Configuring the Voice Interface for Cisco CallManager

•

Configuring the MAC Address Convention

Restrictions for Configuring Auto-Configuration

The following restrictions apply to configuring auto-configuration on the Cisco VG202 and Cisco
VG204 voice gateways before connecting them to the network:

•

The Cisco Unified Communications Manager (CCM) needs to be provisioned with the voice
gateway information.

Summary of Contents for VG202



















































Search results

Summary of Contents for VG202

Reviews:

Related manuals for VG202

Brands by name

Popular brands

Cisco VG202, Software Configuration Manual

Search results

Summary of Contents for VG202

Reviews:

Related manuals for VG202

Brands by name

Popular brands