Cisco VG202 Software Configuration Manual Download Page 17

Page: 17 / 50

2-3

Cisco VG202 and Cisco VG204 Voice Gateways Software Configuration Guide

OL-16191-01

Chapter 2 Using the setup Command Facility

Configuring Global Parameters

Rights clause at FAR sec. 52.227-19 and subparagraph

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, VG20X Software (VG20X-ADVIPSERVICESK9-M), Version

12.4(ORBITTY_APRIL18_POST_SYNC_BUILD.2008-04-17) UBUILDIT Image, CISCO DEVELOPMENT TEST

VERSION

Compiled Fri 18-Apr-08 02:30 by geopasaaniha

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

Cisco VG202 (MPC8300) processor (revision 0x100) with 98304K/32768K bytes of memory.

Processor board ID FOC11334C2B

MPC8300 CPU Rev: Part Number 0x8062, Revision ID 0x11

2 FastEthernet interfaces

2 Voice FXS interfaces

256K bytes of non-volatile configuration memory.

126000K bytes of ATA CompactFlash (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: y

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Step 2

When the following message appears, enter

yes

to begin the initial configuration dialog:

Would you like to enter the initial configuration dialog? [yes/no]:

Step 3

When the following message appears, press

Return

to see the current interface summary:

First, would you like to see the current interface summary? [yes]:

Any interface listed with OK? value “NO” does not have a valid configuration

Interface

IP-Address OK? Method Status Protocol

FastEthernet0/0 unassigned NO unset up up

FastEthernet0/1 unassigned NO unset up down

Step 4

Enter a hostname for the Cisco VG:

Summary of Contents for VG202



















































Search results

Summary of Contents for VG202

Reviews:

Related manuals for VG202

Brands by name

Popular brands

Cisco VG202, Software Configuration Manual

Search results

Summary of Contents for VG202

Reviews:

Related manuals for VG202

Brands by name

Popular brands