Cisco UCS B200 M5 Installation And Service Note Download Page 4

Page: 4 / 74

Internal Components

Diagnostics Button and LEDs

Installing the Front Mezzanine Storage Module

Mini-Storage Module

Embedded SATA RAID Requirements

Embedded SATA RAID Controller Considerations

Embedded SATA RAID: Two SATA Controllers

Enabling SATA Mode

Installing LSI MegaSR Drivers For Windows and Linux

Downloading the MegaSR Drivers

Microsoft Windows Server Drivers

Installing Microsoft Windows Server Drivers

Updating Microsoft Windows Server Drivers

Linux Drivers

Downloading the Driver Image File

Preparing Physical Thumb Drive for Linux

Installing the Red Hat Enterprise Linux Driver

Installing the SUSE Linux Enterprise Server Driver

Removing the Mini-Storage Module

Installing the Mini-Storage Module

Removing the SATA 3.0 M.2 Cards

Installing the SATA 3.0 M.2 Cards

Removing and Installing CPUs and Heatsinks

CPU Configuration Rules

Tools Required for CPU Replacement

Replacing a CPU and Heatsink

Additional CPU-Related Parts to Order with CPU RMA

Supported DIMMs

Installing a DIMM or DIMM Blank

DIMMs and Channels

Memory Performance

Memory Mirroring and RAS

Installing a Virtual Interface Card in the mLOM Slot

Installing a Rear Mezzanine Module in Addition to the mLOM VIC

NVIDIA P6 Graphics Processing Unit

Cisco UCS B200 M5 Blade Server Installation and Service Note

Contents

Summary of Contents for UCS B200 M5











































































Search results

Summary of Contents for UCS B200 M5

Reviews:

Brands by name

Popular brands

Cisco UCS B200 M5, Installation And Service Note

Search results

Summary of Contents for UCS B200 M5

Reviews:

Brands by name

Popular brands